Specifications - Jacuzzi BUILDER Serie Manual De Instalación Y Operación

Important: Read complete instructions before beginning installation.
Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and fittings necessary for
whirlpool operation. An optional drain/overflow kit is available for installation on the bath.
Remove the bath from the carton. Retain the shipping carton until satisfactory inspection of the product has been made. Do not lift the bath
by the plumbing at any time; handle by the shell only.
Immediately upon receipt, inspect the shell before installing. Should inspection reveal any damage or defect in the finish, do not install the
bath. Damage or defect to the finish claimed after the bath is installed is excluded from the warranty. Jacuzzi Whirlpool Bath's responsibility for
shipping damage ceases upon delivery of the products in good order to the carrier. Refer any claims for damage to the carrier. For definitions of
warranty coverage and limitations, refer to the published warranty information packed with the product.
All bath units are factory tested for proper operation and watertight connections prior to shipping. Note: Prior to installation, the bath must
be filled with water and operated to check for leaks that may have resulted from shipping damage or mishandling. Jacuzzi Whirlpool
Bath is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection and testing procedure.
RECTANGULAR BATHS
L
(51 mm)
SIDE VIEW
BATHS WITHOUT INTEGRAL SKIRT
L
SIDE VIEW
BATHS WITH 3-SIDED TILE FLANGE

SPECIFICATIONS

(Rectangular)
MODEL DIMENSIONS
AMIGA™
72" (1829 mm) L
36" ( 914 mm) W
20-3/4" ( 533 mm) H
AMIGA™
72" (1829 mm) L
WITH INTEGRAL
36" ( 914 mm) W
SKIRT
20-3/4" ( 533 mm) H
BIANCA ©
72" (1829 mm) L
48" (1219 mm) W
20-1/2" ( 521 mm) H
CETRA ©
60" (1524 mm) L
WITH INTEGRAL
32" ( 813 mm) W
SKIRT
20-1/2" ( 521 mm) H
CETRA © 532
60" (1524 mm) L
31-7/8" ( 791 mm) W
21-1/4" ( 553 mm) H
CETRA © 536
60" (1524 mm) L
36" ( 914 mm) W
21-1/4" ( 553 mm) H
*Add 1/4" to this dimension when roughing-in for 3-wall niche.
NOTE: The overall dimensions are nominal with a tolerance of +0 and -1/4".
FOR ALL UNITS: Electrical Service Requirements: All require a dedicated GFCI protected separate circuit.
RapidHeat: 115 VAC, 15 AMP, 60 Hz. dedicated GFCI protected separate circuit.
Motor/Pump: 115 VAC, 15 Amp, 60 Hz. dedicated GFCI protected separate circuit.
SPECIFICATIONS
W
2"
H
END VIEW
(25 mm)
W
1"
H
END VIEW
DRAIN/OVERFLOW TOTAL WEIGHT/
DIMENSIONS CUTOUT FLOOR LOADING
70" x 34"
* 16-7/8" (429 mm) A
14" (356 mm) B
NA
* 16-7/8" (429 mm) A
14" (356 mm) B
16" (406 mm) A 70" x 46"
*
8-1/2" (216 mm) B
17-7/8" (454 mm) A NA
*
9-3/8" (238 mm) B
58"
* 18-1/2" ( 470 mm) A
X
9" ( 229 mm) B
30-1/4"
* 58"
18-1/2" ( 470 mm) A
X
9" ( 229 mm) B
34-1/4"
L
SIDE VIEW
BATHS WITH INTEGRAL SKIRT
DRAIN/OVERFLOW
OPERATING
PRODUCT
GALLONAGE
WEIGHT
772 lb 50 U.S. gal 105 lb
(351 kg)/ (186 liters) (48 kg)
43 lb/sq. ft.
(210 kg/sq. m)
796 lb 50 U.S. gal 129 lb
(362 kg)/ (186 liters) (59 kg)
44 lb/sq. ft.
(214 kg/sq. m)
993 lb 73 U.S. gal
135 lb
(451 kg)/ (276 liters)
(61 kg)
41 lb/sq. ft.
(200 kg/sq. m)
46 U.S. gal
727 lb 94 lb
(174 liters)
(330 kg)/ (43 kg)
55 lb/sq. ft.
(268 kg/sq. m)
43 U.S. gal
697 lb 89 lb
(163 liters)
(317 kg)/ (41 kg)
53 lb/sq. ft.
(259 kg/sq. m)
48 U.S. gal
742 lb 92 lb
(181 liters)
(337 kg)/ (42 kg)
50 lb/sq. ft.
(244 kg/sq. m)
1
Jacuzzi Whirlpool Bath© K272000AC 12/04
(25 mm)
W
1"
H
END VIEW
A
B
HEATER READY
FOR FIELD
SKIRT &
INSTALLATION
MOUNTING
Yes
Optional,
(S750000 HEATER KIT)
U-Frame
Integral Yes
(S750000 HEATER KIT)
Yes
Optional,
(S750000 HEATER KIT)
U-Frame
Yes
Integral
(S750000 HEATER KIT)
Yes
Optional
(S750000 HEATER KIT)
U-Frame
Optional
Yes
U-Frame
(S750000 HEATER KIT)