Product Guarantee; Maintenance And Cleaning; Ec Declaration Of Conformity - Novellini 127640 Manual De Instalación, Uso Y Mantenimiento

ENGLISH
HOW TO USE YOUR WHIRLPOOL BATH CORRECTLY:
The benefits of a whirlpool massage:
The swirling water of a whirlpool bath is naturally soothing and
offers many therapeutic benefits. In spas, hydrotherapy is used
to stimulate blood circulation, relax muscles and restore tone to
the skin. Basically, it consists in injecting air into controlled jets of
water of varying intensity directed at the body. The jet of warm
water and air bubbles against the body dilates blood vessels
and increases the flow of blood to the heart. In addition, the
continuous jet of water has a massaging effect on the muscles and
dilates skin pores, promoting the removal of toxins and helping
to hydrate the surrounding tissue. Hydromassage is widely used
by sports people to relieve tired muscles after strenuous physical
activity, producing a pleasant sense of relaxation and well-being.
The jet nozzles can be adjusted to direct the jets at the parts of
the body where you want to concentrate the massaging action.
The temperature of the bath water must never exceed 45°C. The
maximum benefits are obtained with a temperature of 36°-37°C.
ADJUSTING THE JET NOZZLES:
Turn the jet nozzles (C) as required. The nozzles can be pointed
in any direction. Make sure that the nozzles are not clogged and
are not directed upwards (otherwise water will be splashed out
of the tub when the system is switched on). Fill the tub until the
water is well over the level of the jet nozzles (see illustration).
After getting into the bath, the water level must be as shown
in the illustration, otherwise the jets system may not start. The
system features a level sensor which prevents the jets from
switching on if there isn't enough water in the bath. When the
jets system is on, do not use foaming agents such as bubble
baths, soap, etc.
In some types of bath, each whirlpool jet can be individually
adjusted to control the massaging intensity according to taste.

MAINTENANCE AND CLEANING:

The bath is made of acrylic and must be cleaned using a liquid
detergent and a soft cloth or sponge. Use a good quality
household liquid detergent. To prevent scale deposits, wipe dry
using a chammy leather or a soft lint-free cloth that removes
stubborn deposits without leaving traces. Limescale deposits
may be removed using specific detergent products. To restore
shine to the acrylic surface polish with an ordinary wax polish
such as for car bodywork.
DO NOT USE ABRASIVE CLEANERS, ALCOHOL OR ALCOHOL-
BASED PRODUCTS, ACETONE OR OTHER SOLVENTS.
Warning: use of detergents other than those recommended
may damage the bath and/or the whirlpool equipment.
SURFACE SCRATCHES:
Small surface scratches can be removed using wet emery paper
(grade 1000) and then smoothing the surface with abrasive
paste. Once the scratch has been removed, restore surface shine
using wax polish.
TROUBLESHOOTING:
In the event of a problem, perform the following checks before
activating the warranty or contacting qualified staff.
If the jet system does not start:
• If the circuit breaker has tripped, reset it and try switching on
the jet system again.
• If the pump does not start when the water level is well above
the nozzles.
• Check to ensure that the cut-out is turned on.
• Check if an alarm has been raised (see menu).
If the jet system does not stop:
• If the pump continues running and cannot be turned off using
the usual controls, turn it off using the circuit breaker and try
again.
Do not make adjustments to the wiring or other electrical
parts.
DISPOSING OF THE WHIRPOOL BATH:
For the disposal of the product or its parts, follow the local
regulations on matters of waste disposal. For Italy, Legislative
Decree n. 152 of April 3, 2006 will hold, and for the other EU
countries, Directive 2008/98/EC.

PRODUCT GUARANTEE:

All products purchased by consumers, as defined in Article 3 of
the Consumer Code (Legislative Decree no. 206 of 6 September
2005 and subsequent amendments), are covered by the legal
guarantee of the seller under Article 128 and subsequent
amendments of the consumer Code. In case of lack of conformity
of the product, we invite the consumer to contact their dealer
within the statutory deadline.

EC DECLARATION OF CONFORMITY:

The manufacturer Novellini S.p.a., Via Mantova, 1023 - 46030
Romanore di Borgo Virgilio, Mantova - Italy Declares under its
responsibility that the following products:
whirlpool baths mod. 500/10 500/20 500/30 are in conformity
with the following European directives: 2006/95/CE, 2004/108/
CE and EU regulation 305/2011 and subsequent amendments,
with reference to harmonized standards:
EN55014-1
EN55014-2
EN60335-2-60
EN12764
Conforms with the European ROHS directives
And was manufactured in conformity with the European
Directive 2011/65/EU, and that the maximum concentration
allowed for the following substances have been fully complied
to.
- Mercury (Hg), 0.1% max.
- Cadmium (Cd), 0.01% max.
- Lead (Pb), 0.1% max.
- Chromium VI (hexavalent chromium) (Cr(VI)), 0.1% max.
- PBB (polybrominated biphenyls), 0.1% max.
- PBDE (Polybrominated diphenyl ether), 0.1% max.
-30-