Tabla de contenido
Idiomas disponibles
Idiomas disponibles
• 3440093 Very fine cut, for soft, hard wood and chip-
board up to 30 mm (HCS, pitch 2.5 mm, length 75 mm)
• 3440163 Very fine cut, for soft, hard wood and chip-
board up to 30 mm (HCS, pitch 2.5 mm, length 105 mm)
• 3440097 Very fine cut, for soft, hard wood and chi-
pboard up to 80 mm. For linoleum and flexible plastics
up to 8 mm (HCS, pitch 4 mm, length 105 mm)
• 3440164 Very fine cut, for soft, hard wood and chi-
pboard up to 80 mm. For linoleum and flexible plastics
up to 8 mm (HCS, pitch 4 mm, lenght 105 mm)
• 3440096 Rough cut, for soft and hard wood up to
60 mm. For expanded polyurethane up to 40 mm (HCS,
pitch 3 mm, length 75 mm)
• 3440098 For soft steel up to 3 mm. Aluminium and
non ferrous metals up to 4 mm. Melamine and synthetic
fibres up to 8 mm (HCS, pitch 1.2 mm, length 52 mm)
• 3440165 For soft steel up to 3 mm. Aluminium and
non ferrous metals up to 4 mm. Melamine and synthetic
fibres up to 8 mm (BIM, pitch 1.2 mm, length 105 mm)
• 3440099 For soft steel up to 6 mm. Aluminium and
non ferrous metals up to 8 mm. Melamine and synthetic
fibres up to 10 mm (HSS, pitch 2 mm, length 52 mm)
• 3440166 For soft steel up to 6 mm. Aluminium and
non ferrous metals up to 8 mm. Melamine and synthetic
fibres up to 10 mm (BIM, pitch 2 mm, length 105 mm)
• 3440100 For soft steel up to 6 mm. Aluminium and non
ferrous metals up to 8 mm. Cement fibres and synthetic
materials up to 10 mm (HSS, pitch 3 mm, length 52 mm)
15. MAINTENANCE
Always be sure that the tool is switched
off and the battery cartridge is removed
before adjusting or checking function
on the tool.
• Saw blade inspection: Only sharp blades in perfect
condition should be used. Cracked, bent or jagged saw
blades should be immediately replaced.
• Inspect the mounting screws: Regularly inspect all
the mounting screws and ensure they are firmly tighte-
ned. Should any screw be loose, tighten it immediately.
Failure to do so could put you at serious risk.
• Always keep the vents clean and free of obstruction.
• Clean the machine thoroughly after each use. Blast
the motor regularly with compressed air.
• The saw blade retaining lever ("Quick Fix" systems) must
be regularly cleaned, especially when sawing material
which produces large amounts of dust. This will ensure
correct retaining lever operation.
• The saw blade guide should be lubricated now and
again with a drop of oil and, at the same time, checked
for wear. If it is worn, after prolonged use, it should be
replaced at the VIRUTEX Technical Assistance Centre.
• Greasing
(to be performed by an official technician)
The screws on the gear head must not be loosened
during the warranty period. Otherwise the warranty
will be invalid.
The grease should be renewed after 1,500 hours of use.
16. BATTERY MAINTENANCE
• Charge the battery cartridge 7 (Fig. 0) before com-
pletely discharged. Stop operation in low power and
charge it immediately.
• Do not overcharge when the battery 7 is full, other-
wise it will shorten the life time.
• Charge the battery cartridge 7 with room temperature
at 10° C - 40° C (50°F to 104°F). Charging the battery
in temperatures out of this range can damage it and
may cause fire.
• Charge battery 7 every 6 months without operation
for a long time.
• Replace worn out batteries in time. Decline of pro-
duction or a significantlyshorter runtime of the power
tool after charging indicates aging of the battery 7
and the need for replacement. It should be taken into
account that the battery 7 may discharge faster if the
works take place in the temperature below 0°.
• In case of long time storage without use, it is recom-
mended to store the battery 7 at room temperature, it
should be charged to 50%.
Technical service:
a) To maintain product safety and reliability, repairs, any
other maintenance or adjustment should be performed
by authorized service senters, always using original
replacement parts.
b) Do not repair damaged batteries. Maintenance of the
batteries should be performed only by their producer or
authorized service center.
Transport of Li-Ion batteries
The contained Li-Ion batteries are subject to the
Dangerous Goods Legislation requirements. The user
can transport the batteries by road without further
requirements.
When being transported by third parties (e.g.: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed. For prepa-
ration of the item being shipped, consulting an expert
for hazardous material is required.
Dispatch batteries only when the housing is undamaged.
Tape or mask off open contacts and pack up the battery
in such a manner that it cannot move around in the
packaging. Please also observe possibly more detailed
national regulations
17. NOISE AND VIBRATION LEVELS
The noise and vibration levels of this device have
15
Tabla de contenido
