Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 13

Enlaces rápidos

Models 355 and 355–EU Random Orbital Sanders are designed for precise and sophisticated
automotive sanding and finishing operations.
Ingersoll–Rand is not responsible for customer modification of tools for applications on which
Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand
held/hand operated pneumatic tools.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 5/16" (8 mm) inside diameter air supply
hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 2000
Printed in U.S.A.
INSTRUCTIONS FOR
MODELS 355 AND 355–EU
RANDOM ORBITAL SANDERS
03538188
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away
from rotating end of tool.
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.
Tool shaft may continue to vibrate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
Form P6960
GB
Edition 4
January, 2000
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 355

  • Página 13: Utilización De La Herramienta

    MODELOS 355 Y 355–EU NOTA Las lijadoras orbitales variables modelos 355 y 355–EU están diseñadas para trabajos precisos y sofisticados de lijado y acabado en la industria de la automoción. Ingersoll–Rand no aceptará responsabilidad alguna por la modificación de las herramientas efectuada por el cliente para las aplicaciones que no hayan sido consultadas con Ingersoll–Rand.
  • Página 14: Etiquetas De Aviso

    Diámetro del disco Tipo de disco dB (A) vibraciones •Potencia pulg. Presión 355, 355–EU 10.000 Vinilo circular 85,1 98,1 Probado en conformidad con ANSI S5.1–1971 lijando sobre pieza de acero ♦ Probado en conformidad con ISO8662–1 lijando sobre pieza de acero •...
  • Página 15: Declaración De Conformidad

    (nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Lijadora Orbitale Variable Modelo 355–EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE ISO8662 conforme a los siguientes estándares:...
  • Página 19 351–283 24 Rotor ..... 355–53 Vacuum Adapter ... . .
  • Página 20 Service Centers Centres d’entretien Ingersoll–Rand Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll–Rand Nederland Produktieweg 10 2382 PB Zoeterwoude Nederland Tel: (31) 71 452200 Fax: (31) 71 218671 Ingersoll–Rand Company 510 Hester Drive Ingersoll–Rand Company SA White House PO Box 3720 TN 37188 Alrode 1451...
  • Página 37 Servicentre Servicecenter Servicesenter Huoltokeskus Service Centra Ingersoll–Rand Nederland Produktieweg 10 2382 PB Zoeterwoude Nederland Tel: (31) 71 452200 Fax: (31) 71 218671 Ingersoll–Rand Company 510 Hester Drive Ingersoll–Rand Company SA White House PO Box 3720 TN 37188 Alrode 1451 South Africa Tel: (615) 672 0321 Tel: (27) 11 864 3930 Fax: (615) 672 0801...

Este manual también es adecuado para:

355-eu

Tabla de contenido