Ingersoll Rand 359 Instrucciones
Ingersoll Rand 359 Instrucciones

Ingersoll Rand 359 Instrucciones

Lijadoras orbitales
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 13

Enlaces rápidos

MODELS 359 AND 359–EU ORBITAL SANDERS
Models 359 and 359–EU Sanders are designed to perform sanding operations on surfaces
that are painted, or made of metal, fiberglass, wood, body filler and numerous other
materials.
Ingersoll–Rand is not responsible for customer modification of tools for applications on
which Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand
held/hand operated pneumatic tools.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 5/16" (8 mm) inside diameter air supply
hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905–1 for a
typical piping arrangement.
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 2000
Printed in U.S.A.
INSTRUCTIONS FOR
NOTE
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating
this tool.
Keep hands, loose clothing and long hair away
from rotating end of tool.
Anticipate and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.
Tool pad may continue to vibrate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
NOTE
03538204
Form P6962
Edition 4
February, 2000
GB
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 359

  • Página 13: Para Poner La Herramienta En Servicio

    INSTRUCCIONES PARA LIJADORAS ORBITALES VARIABLES MODELOS 359 Y 359–EU NOTA Las lijadoras modelo 359 y 359–EU están diseñadas para realizar trabajos de lijado en superficies pintadas, metálicas, de fibra de vidrio, madera, tapaporos y diversos otros materiales. Ingersoll–Rand no aceptará responsabilidad alguna por la modificación de las herramientas efectuada por el cliente para las aplicaciones que no hayan sido consultadas con Ingersoll–Rand.
  • Página 14: Etiquetas De Aviso

    Velocidad en vacío dB (A) vibraciones pulg. Presión Potencia 359, 359–EU 3–2/3 x 9 93 x 228 8.000 78,4 ––– Probado en conformidad con ANSI S5.1–1971 lijando sobre pieza de acero ♦ Probado en conformidad con ISO8662–1 lijando sobre pieza de acero...
  • Página 15: Declaración De Conformidad

    (nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Lijadoras orbitales variables modelo 359–EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE ISO8662 conforme a los siguientes estándares:...
  • Página 19 Counterbalance ....359–236 for 359 ....351–273 Housing .
  • Página 20 Service Centers Centres d’entretien Ingersoll–Rand Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll–Rand Nederland Produktieweg 10 2382 PB Zoeterwoude Nederland Tel: (31) 71 452200 Fax: (31) 71 218671 Ingersoll–Rand Company 510 Hester Drive Ingersoll–Rand Company SA White House, TN 37188 PO Box 3720 Alrode 1451 Tel: (615) 672 0321...
  • Página 37 Servicentre Servicecenter Servicesenter Huoltokeskus Centro de Serviço Ingersoll–Rand Nederland Produktieweg 10 2382 PB Zoeterwoude Nederland Tel: (31) 71 452200 Fax: (31) 71 218671 Ingersoll–Rand Company 510 Hester Drive Ingersoll–Rand Company SA White House, TN 37188 PO Box 3720 Alrode 1451 Tel: (615) 672 0321 South Africa Fax: (615) 672 0801...

Este manual también es adecuado para:

359-eu

Tabla de contenido