Ingersoll Rand 319 Manual De Instrucciones
Ingersoll Rand 319 Manual De Instrucciones

Ingersoll Rand 319 Manual De Instrucciones

Ocultar thumbs Ver también para 319:
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 13

Enlaces rápidos

The Models 319 and 319- -EU Sanders are designed for heavy- -duty rust removal and
metal and body filler sanding for paint preperation.
Ingersoll- -Rand is not responsible for customer modification of tools for applications
on which Ingersoll- - Rand was not consulted.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand
held/hand operated pneumatic tools.
For safety, top performance, and maximum
durability of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 3/8" (10 mm) inside diameter air supply
hose.
Always turn off the air supply and disconnect the
air supply hose before installing, removing or
adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905- - 1 for a
typical piping arrangement.
Keep clear of whipping air hoses. Shut off the
compressed air before approaching a whipping air
hose.
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged
label.
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating
this tool.
The use of other than genuine Ingersoll- - Rand replacement parts may result in safety hazards, decreased tool
performance, and increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll- - Rand Authorized
Servicenter.
Refer All Communications to the Nearest
Ingersoll- - Rand Office or Distributor.
 Ingersoll- - Rand Company 2001
Printed in U.S.A.
INSTRUCTIONS FOR
MODELS 319 AND 319- -EU SANDERS
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
03535374
Keep hands, loose clothing, long hair and jewelry
away from rotating end of tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. Anticipate and
be alert for sudden changes in motion, reaction
torques, or forces during start- - up and operation.
Tool shaft may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using
any tool if discomfort, tingling feeling or pain
occurs. Seek medical advice before resuming use.
Use accessories recommended by Ingersoll- - Rand.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
Prevent exposure and breathing of harmful dust
and particles created by power tool use:
Some dust created by power sanding, sawing,
grinding, drilling and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- - lead from lead based paints,
- - crystalline silica from bricks and cement
and other masonry products, and
- - arsenic and chromium from chemically
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specially designed to
filter out microscopic particles.
GB
Form P6837
Edition 5
September, 2001
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 319

  • Página 13: Utilización De La Herramienta

    MODELO 319 Y 319- -EU NOTA Las lijadoras modelo 319 y 319- -EU están diseñadas para la eliminación de óxido de servicio pesado y el lijado de metal y masilla de carrocería para preparación para pintura. Ingersoll- -Rand no aceptará responsabilidad alguna por la modificación de las herramientas efectuada por el cliente para las aplicaciones que no hayan sido consultadas con Ingersoll- -Rand.
  • Página 14: Identificación De Símbolos De Aviso

    (A) vibraciones Presión •Potencia 319, 319- - EU Palanca 5/8 pulg.- - 11 5.000 diámetro 7 pulg. 90,8 103,8 Probado en conformidad con ANSI S5.1- - 1971 lijando sobre pieza de acero ♦ Probado en conformidad con ISO8662- - 1 lijando sobre pieza de acero ISO3744 •...
  • Página 15: Declaración De Conformidad

    (nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ, U.K. (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Lijadoras Modelo 319- EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE ISO8662 conforme a los siguientes estándares:...
  • Página 19 Motor Housing Assembly ..318- - A40 Pinion ..... 319- - 551 Housing Plug ... . . 318- - 504 Pinion Retaining Ring .
  • Página 20 Service Centers Centres d’entretien Ingersoll- -Rand Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll--Rand Nederland Produktieweg 10 2382 PB Zoeterwoude Nederland Tel: (31) 71 452200 Fax: (31) 71 218671 Ingersoll--Rand Company 510 Hester Drive Ingersoll--Rand Company SA White House, TN 37188 PO Box 3720 Alrode 1451 Tel: (615) 672 0321...

Este manual también es adecuado para:

319--eu

Tabla de contenido