Cebora SOUND MIG MIG 3540/T STAR PULSE Manual De Instrucciones página 18

pole. Make sure that the supply voltage corresponds to
the rated voltage of the welding machine.
Size the protective fuses based on the data listed on the
technical specifications plate.
Position the cylinder onto the support O fasten it with
belts P and connect the gas hose to the pressure reduc-
ing valve. Mount the welding torch.
To make sure that the groove of the rollers matches the
wire diameter used, open the mobile lateral side, remove
the cover CA, release the wire press rollers by means of
the pressure adjusting knob BN, replace the rollers and
remount the cover CA. (See fig. 5).
Fig. 5
BN
CA
Mount the wire coil and slip the wire into the feeder and
welding torch sheath.
Block the wire press rollers with the knob BN and adjust
the pressure.
Turn on the machine.
Adjust the gas by means of key AY and then feed the wire
by means of key AW.
7 WELDING
Welding Synergic Pulsed MiG LED AP on.
Select the PRG number based on the wire diameter to be
used, the type and quality of the material, and the type of
gas, using the instructions located inside the wire feeder
compartment.
Set the functions in the submenu according to the
instructions under paragraph «Service functions».
5.2.3The welding parameters are set by means of knobAI.
Synergic MiG Welding LED AQ on.
Select the PROG number based on the wire diameter to
be used, the type and quality of the material, and the type
of gas, using the instructions located inside the wire feed-
er compartment.
Set the functions in the submenu according to the
instructions under paragraph «Service functions».
Adjust the wire speed and the welding voltage using the
knob AI.
Conventional MiG Welding LED AR on.
Select the PROG number based on the wire diameter to
be used, the type and quality of the material, and the type
18
of gas, using the instructions located inside the wire feed-
er compartment.
Set the functions in the submenu according to the
instructions under paragraph «Service functions».
Adjust the wire speed and the welding voltage using the
knob AI. and AN respectively.
TIG Welding LED AS ON.
Plug in the 19-pin connector of the TIG welding torch into
socket 193, located on the front control panel and the
power connector to the negative pole A . Connect the
earth cable to the positive pole D.
Set the functions in the submenu according to the
instructions under paragraph «Service functions».
Adjust the welding current using the knob. AI.
MMA Welding LED AT on.
Connect the earth terminals and the cable terminals of
the electrode clamp to terminals DandA observing the
polarity stated by the electrode manufacturer. Set the
BN
functions in the submenu according to the instructions
under paragraph «Service functions».
Adjust the welding current using the knob. AI.
8 ACCESSORIES
8.1 CURRENT ADJUSTMENT TRAY ART.
187 (POTENTIOMETER) + EXTENSION CABLE
(5m)(ART. 1192 + ADAPTER CABLE ART. 1191
Possible adjustments during welding processes:
MMA: The tray adjusts the current from a minimum value
(10A) to the current set on knob AI on the control panel.
TIG: The tray executes the same function as MMA.
8.2 FOOT ART.. 193 + ADAPTER CABLE ART. 1191
To be used with TIG Process Welding.
The current is adjusted by this accessory while the start
control is activated by means of the welding torch button.
The current may be adjusted from a minimum value to the
maximum value set by means of knob AI on the control
panel.
8.3 TIG WELDING TORCH ART.. 1256
BINZEL water-cooled TIG welding torch (450A) – m4. 4.
8.4 TIG WELDING TORCH ART. 1258
BINZEL water-cooled TIG welding
UP/DOWN mt. 4.
8.5 Connection ART. 1165 between the power source
and the Binzel TIG welding torches.
8.6 MIG WELDING TORCH ART. 1242
Air-cooled CEBORA MIG welding torch 280 A 3,5.
8.7 MIG WELDING TORCH ART. 1239
Water-cooled CEBORA MIG welding Torch 280 A m 3,5.
8.8 MIG WELDING TORCH ART. 1241
Water-cooled
UP/DOWN m 3,5.
The U/D L.H control:
CEBORA MIG welding Torch 380 A
torch (450A) –