Tabla de contenido
Idiomas disponibles
Idiomas disponibles
GB
Welding Safety
WARNING: DO NOT strike an arc close to the gas bottle.
WARNING: DO NOT lift the welder with a gas bottle attached.
WARNING: DO NOT use a welder for pipe thawing.
WARNING: AVOID unintentional arcing of the welder. Switch off the welder when not in use.
IMPORTANT: Use of welding machines creates powerful magnetic fields. This may disturb the
operation of sensitive electronic equipment. Pacemaker wearers should consult a doctor before using
a welding machine.
IMPORTANT: Do not overload a mains circuit. Check that your mains wiring is capable of
delivering the required current safely. If unsure consult a professional electrician before use.
• Welding produces toxic fumes and can reduce oxygen levels in the work area. Always
work in a well-ventilated area. Avoid inhaling welding fumes, use a suitable respirator where
appropriate
• Some metal parts may have zinc, lead, cadmium or other coatings. Attempting to weld
through these coatings can produce highly toxic fumes. Always remove all coatings before
welding
• If you experience irritation to the lungs, throat or eyes whilst welding, STOP IMMEDIATELY
and seek fresh air
• Welding produces extremely high levels of UV light. To prevent eye damage, ALWAYS use
an approved welding face mask. Under no circumstances look directly at the arc
• The light produced when arc welding can be attractive to look at, especially to children.
Always prevent other people from viewing the arc welding light with unprotected eyes
• If there is a possibility of other people approaching the work area, erect suitable
screening to protect them from the light / glare
• Always replace the welder face mask glass as soon as it shows any signs of wear or
damage
• To prevent skin damage, ALWAYS wear a suitable fire-proof long sleeved jacket, heat proof
gloves, and cap. Keep covered up
• Always remove any flammable materials (e.g. cigarette lighter, matches) from your
clothing before welding
• Always keep a fire extinguisher nearby when welding
• Sparks generated while welding can ignite flammable materials easily in the welding
area. So it is important to remove flammable materials before commencing welding
• Only weld when the work area and all workpieces are dry
• Do not weld sealed containers (e.g. fuel tanks, air tanks, oil drums). The heat generated
from welding can cause sealed containers to burst without warning
• Be aware of transferred heat. Metal parts can conduct heat away from the work area and
cause ignition of flammable materials
• Be aware that welded parts will remain hot for some time after joining. Allow to cool
completely before handling, or leaving unattended
• Never weld where flammable gases, liquids or dust are present
• Ensure that there is always a responsible person nearby to alert you to any fire, or to call
help in an emergency
• Workpieces with burred edges can damage the torch cable. Always ensure the torch cable
will not be damaged as it moves over a surface
Wire feed
• Caution: The tip of welding wire can be very sharp, and is fed with adequate force to
puncture skin
• Keep the welding machine switched off until you are ready to begin welding. Never point
the torch towards people or animals
8
Product Familiarisation
1
Carrying Handle
2
Rating Label
3
Power Light
4
Extended Handle
5
Over-Heat Indicator
6
Wire Feed Speed Dial
7
Voltage/Current Selector
8
Mains Cable
9
Earth Clamp
10 Tip
11 Shroud
12 Trigger
13 Torch Handle
14 Torch Cable
15 Wheel
16 Panel Release
17 Rollers Cover
18 Lower Roller
19 Roller Tension Adjuster
20 Wire Input
21 Upper Roller
22 Tip Holder
23 Spool Nut
24 Tension Spring
25 Spool Retainer
26 Wire Spool
27 Spool Thread
28 Filter Frame
29 Welding Filter
30 Spatter Shield
31 Frame Clips (x 2)
32 Handle Nuts (x 3)
33 Handle Bolts (x 3)
34 Frame Screws (x 2)
35 Handle
36 Welding Mask
Accessories (not shown)
• Hammer Brush
• 0.6mm tip
Tabla de contenido
Solución de problemas
