Tabla de contenido
OBJ_BUCH-1841-002.book Page 13 Tuesday, June 11, 2013 1:11 PM
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9
D-70745 Leinfelden-Echterdingen
Henk Becker
Helmut Heinzelmann
Executive Vice President
Head of Product Certification
Engineering
PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
08.06.2013
Assembly
Before any work on the machine itself, pull the mains
plug.
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Mounting the Auxiliary Handle (see figure A)
Operate your machine only with the auxiliary handle 3.
Screw the auxiliary handle 3 on the right or left of the machine
head depending on the working method.
Adjusting the Sanding Attachment (see figure B)
– Before adjusting the sanding attachment 10, completely
release clamping lever 5.
– Move the sanding attachment 10 accordingly to suit your
working conditions and working position.
– Close the clamping lever 5 and tighten it firmly.
Note: Clamping lever 5 is indexed (adjustable), allowing it to
be set to an ergonomically favourable or space-saving posi-
tion.
With the clamping lever 5 tightened, pull its lever away from
the machine head, turn it to the desired position and allow it
to engage again.
Changing the Sanding Belt (see figure C)
– Loosen fastening screw 9 and remove the attachment cov-
er 8.
– Press sanding attachment 10 via the supporting surface 14
against a sturdy object (e. g. a bench top) until the sanding
attachment 10 deflects. Remove the sanding belt 12.
Bosch Power Tools
– Firstly, position the new sanding belt 12 around on the
drive roller 7 and then around the deflection roller 13. Pay
attention that the arrow directions on the inside of the
sanding belt (if given) and on the attachment cover 8 of the
power tool correspond. Release the sanding attachment
10 again, so that the sanding belt 12 is tensioned.
– Mount the attachment cover 8 with fastening screw 9.
– Adjust the belt run as required, see section "Adjusting the
Belt Run".
Adjusting the Belt Run (see figure D)
Adjust the belt run only when the power tool is
switched off and disconnected from the power supply.
Turn adjustment screw 1 until the sanding belt 12 is posi-
tioned centred on deflection roller 13.
Selecting the Sanding Belt
Depending on the material to be worked and the required rate
of removal, different sanding belts are available:
For dry sanding and pre-sanding
For structuring and for smoothing
out minor unevenness
For fine structuring
Polishing
Note: Depending on the application method and the material
being worked, either flexible of stiff sanding belts can be
used.
Changing the Sanding Arm (see figure E)
– Remove the sanding belt 12 (see section "Changing the
Sanding Belt").
– Unscrew adjustment screw 1 and remove the sanding arm
16.
– Mount the new sanding arm 16 and fasten it with adjust-
ment screw 1.
– Pay attention that the sanding arm 16 is correctly mounted
according to figure E.
– Mount the sanding belt 12 (see section "Changing the
Sanding Belt").
– Adjust the belt run (see section "Adjusting the Belt Run").
Operation
Starting Operation
Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified on
the nameplate of the machine. Power tools marked
with 230 V can also be operated with 220 V.
Switching On and Off
To start the power tool, push the On/Off switch 4 forwards.
To switch off the machine, push On/Off switch 4 toward the
rear.
To save energy, only switch the power tool on when using it.
English | 13
Grain size
coarse
40, 60
medium 80, 120
180
fine
Fleece belts
Fleece belts
3 609 929 C46 | (11.6.13)
Tabla de contenido
