Idiomas disponibles
Idiomas disponibles
ENGLISH
PROGRAMMABLE TIMER
You can program your heater to turn on at a
preset time or turn off after a set amount of time.
RETAIN THE FOLLOWING FOR FUTURE
Setting the On Timer:
REFERENCE.
1. With the heater off, press and hold (+) and
(-) simultaneously until the display flashes.
DESCRIPTIONS (See Fig.1 & 2)
2. Press (+) or (-) to select the amount of time
A. Left End Cap
you would like to pass before the heater
B. Rear Housing
turns on.
C. Right End Cap
3. After setting the timer, the display shows a red dot
D. Display
next to the current room temperature on the
E. Mode Indicator Lights
display to indicate that the timer is activated.
F. Mode Button
4. After the programmed length of time has
G. Thermostat Adjustment Buttons
passed, the heater automatically turns on
H. Foot Base (2)
Auto HI at 24°C (75°F) for 2 hours.
I. Grill
Setting the Off Timer:
Foot Assembly (See Fig.3)
1. Select the desired mode and/or temperature.
1. Insert Left Foot Base H(l) into Left End Cap
2. With the heater running, press and hold (+)
(A) and tighten the Screw.
and (-) simultaneously until the display flashes.
2. Insert Right Foot Base H(r) into Right End
3. Press (+) or (-) to select the amount of time
Cap (C) and tighten the Screw.
you would like the heater to run.
4. After setting the timer, the display shows a
Wall Mounting Assembly
RED dot next to current room temperature on
(See Fig.4 - Fig.6)
the display to indicate that the timer is activated.
IMPORTANT: Before drilling into any wall
5. The heater automatically shuts off after the
ensure no electrical cables are present in the area.
programmed length of time has passed.
1. Remove Base Feet (H) from the End Caps
(A and C), if installed.
FROST GUARD
2. Secure the Mounting Bracket to the wall.
Press the (
3. Hang the main body on the Mounting Bracket.
times for Anti Frost setting (AF will show in
the digital display).
SETTING THE THERMOSTAT
1. Press (
) Mode button (F):
This special setting is automatically activated
•
1
= LO; runs continuously on low.
when the (AF) mode is selected. In this mode, the
st
heater is off until the room's temperature reaches
•
2
= HI; runs continuously on high.
nd
freezing and the heater automatically turns on HI
•
3
= Auto Low; press (+) or (-) to set
rd
power. The heater will cycle ON and OFF as it
desired temperature.
maintains the temperature between 5-8 °C.
•
4
= Auto HI; press (+) or (-) to set
th
desired temperature.
AUTO SAFETY SHUT OFF
2. Once you have selected the mode and
temperature, the display returns to the
The heater has a built in safety device which will
current room temperature and gradually
switch off the heater automatically in case of
increases as the room warms.
accidental overheating. It can only resume
3. If you selected an Auto mode and the heater
operation when the user has reset the unit. (OH)
does not start, make sure the set temperature
will display in a overheat situation.
is higher than the current room temperature.
To reset the heater:
1. Unplug the heater and wait for 30 minutes
for the heater to cool down.
N N O O T T E E : : In Auto mode, it is normal for
the heater to cycle ON and OFF as it
2. After the 30 minutes, plug the heater in
maintains the programmed temperature.
again and operate normally.
To prevent the unit from cycling, raise
SAFETY BACK-UP FUSE
the thermostat setting.
In the unlikely case the heater does not respond
to an overheat situation, the safety back-up fuse
The Thermostat remembers the
will engage. In this case, the heater will not reset.
previous temperature setting after
Please contact your local service number for advice.
the unit is turned off. However, if
the unit is unplugged, the digital
TIP OVER PROTECTION
thermostat resets and no longer
When the unit is accidentally knocked over, it
remembers the previous
will instantly shut off. To reset, simply place the
temperature setting.
2
All manuals and user guides at all-guides.com
heater in an upright position. Press the (
MODE button again.
BATHROOM USE
•
If this heater is going to be used in a
bathroom, or similar room, it must be installed:
a. In such a way that the switches and other
controls cannot be touched by the person
in the bath or shower.
b. Outside the grey shaded areas (Fig.7).
•
If you are unsure about the installation of this
heater in the bathroom we recommend that
you seek advice from a professional
electrician/installer.
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety
precautions should always be taken including
the following:
1. Before connecting the heater, check that the
voltage indicated on the rating plate
corresponds to the main voltage in your
home/office.
2. WARNING: In order to avoid overheating,
do not cover the heater (
3. DO NOT position the heater directly under a
power socket.
4. Do not use this heater in the immediate
) Mode button 5 consecutive
surroundings of a bath, a shower or a
swimming pool.
5. If the supply cord or plug is damaged, it must
be replaced by the manufacturer or its service
agent or similarly qualified person in order to
avoid hazard. The heater contains no user
serviceable parts. Should the product suffer
damage or breakdown, it must be returned to
the manufacturer or their service agent.
6. Under the environment with electrical fast
transient, the product may malfunction and
require user to reset the product.
7. Do not use this heater with a programmer,
timer or any other device that switches the
heater on automatically, since a fire risk
exists if the heater is covered or
positioned incorrectly.
8. Only touch the heater with dry hands.
9. DO NOT use this heater outdoors.
10. DO NOT position where it can be touched by
children, especially the very young.
11. Allow a safe area around the heater away
from furniture or other objects; at least 50
cm from the top and sides and 200 cm at
the front.
12. Do not use this heater when it is lying on
its side.
13. DO NOT use the heater in rooms with
explosive gas (e.g. petrol) or while using
inflammable glue or solvent (e.g. when
gluing or varnishing parquet floors, PVC etc.)
)
14. DO NOT insert any objects into the heater.
15. Keep the mains cord at a safe distance from
the main body of the heater.
16. If overheating should occur, the built-in
overheating safety device will switch off
the heater.
17. Do not place the cord under a rug.
18. The heater is to be installed so that switches
and other controls cannot be touched by a
person in the bath.
19. Heater must be installed at least 0.6 m
above the floor.
20. The heater cannot be used adjacent to
curtains or combustible material. Curtains or
combustible material may be burned if the
heater was installed incorrectly.
21.This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that
).
they do not play with the appliance.
22. WARNING: Risk of Fire. Discontinue use if the
outlet or plug become hot to the touch.
Overheating may indicate a worn or damaged
outlet. Consult a qualified electrician for
outlet replacement.
23. CAUTION: In order to avoid a hazard due
to inadvertent resetting of the thermal cut-
out,this appliance must not be supplied
through an external switching device, such
as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
ESPAÑOL
LEA LO SIGUIENTE Y GUÁRDELO
PARA CONSULTAS FUTURAS
DESCRIPCIONES (Ver Fig. 1 & 2)
A. Tapa lateral izquierda
B. Carcasa posterior
C. Tapa lateral derecha
D. Pantalla
E. Indicadores luminosos de modo
F. Botón de modo
G. Botones de ajuste del termostato
H. Patas de la base (2)
I. Rejilla
Ensamblaje del pie (Véase la Figura 3)
1. Inserte la base del pie izquierdo H(i) en la
funda del extremo izquierdo (A) y apriete
el tornillo.
3
