Installing The Product; Product Installation; Electrical Connections; Setting Of The Mechanical Limit Switch While - Key Automation RAY2524 Instrucciones Y Advertencias Para Su Instalación Y Uso

Motorreductor para cancelas batientes
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 20

4 - PRODUCT INSTALLATION

4.1 - Installation
Before proceeding with the installation, check the integrity of the
product and that all components are present in the package (Fig. 3).
Also make sure that the mounting area of the gear motor is
compatible with the dimensions (Fig. 1).
Check the permitted opening angle, based on the mounting points of
the brackets with the graph (Fig. 5).
Fig.6 shows a typical installation:
- Gear motors
- Photocells
- Columns for photocells
- Flashing light with antenna
- Key switch or digital keypad
- Control unit
Installing the rear fixing bracket
The fixing position of the rear bracket is determined according to the
graph (Fig. 5).
Important: installations where the values of "A" and "B" (Fig. 5) are
as similar to each other as possible are preferred (l.o.= optimal line).
If necessary, cut the rear bracket (Fig. 7) to obtain the value "B", then
weld the fixing bracket to the wall.
Secure the bracket to the wall using welding, screws or bolts (not
included).
Installing the front fixing bracket
The front bracket must be fixed to the door according to dimension
"D" of Table 1.
Note: If you mount the closing limit switch, reduce the value "E" of
40 mm.
The front bracket must be fixed as the same height as the rear
bracket (Fig.8).
Installing the gear motor
Open the release door and remove the 2 screws that secure the rear
cover (Fig. 9A).
Remove the top cover first sliding it slightly backward (Fig. 9A)
Place the gear motor against the rear bracket and insert the fixing

4.2 - Electrical connections

Loosen the cable gland and insert the power cord (Fig. 12).
connect the wires of the power cable to the terminal block
according to the wiring diagram (Fig. 13).
Screw the cable gland.
4.3 - Setting of the mechanical limit switch while opening
Release the gear motor (Fig.10).
Loosen the screw on the mechanical limit switch until it is able to
slide.
Open the door manually to the point of desired opening.
Bring the mechanical limit switch up to pin of the slide bracket and
secure it with the screw (Fig. 11).
4.4 - Replacement of the leds
Turn off the power supply.
With the help of a screwdriver remove the lower screw (Fig. 14a).
Remove the cover and the LED strip (Fig.14a).
Disconnect the connector (Fig. 14b).
screw (Fig.9B).
Insert the pin of the sliding bracket into the bush of the front bracket
and secure it with the screw and washer provided (Fig.9C).
Tighten the screw on the rear bracket previously mounted with the
nut (Fig.9D).
A
100
110
120
130
140
150
160
170
180
190
200
210
220
230
A= distance between the hinge axis and the axis of the hole for the
rear mounting.
E= distance between the hinge axis and the axis of the hole for the
front mounting.
Replace the top cover first sliding it slightly backward.
Open the door and tighten the 2 screws that secure the rear cover.
If you need to also adjust the mechanical limit switch in closing
(optional), repeat the same procedure, this time manually bringing
the door to the point of closure you want.
Connect the new LEDs and insert them into the mask.
Insert the mask first inserting the side of the seal and then securing
it with the screw.
EN
E
650
640
630
620
610
600
590
580
570
560
550
540
530
520
11
Tabla de contenido
loading

Este manual también es adecuado para:

Ray2524e

Tabla de contenido