Cleaning And Maintenance; Ordering Accessories; Guarantee And Support; Troubleshooting - Philips AT621 Manual De Instrucciones

Dry shaving
1 Switch on the appliance.
2 Move the shaving heads over your skin in circular movements (Fig. 6).
Note: Circular movements provide better shaving results than
straight movements.
3 Clean the shaver after use.
Trimming (AT621, AT620 only)
You can use the trimmer to groom your sideburns and moustache.
1 Push the trimmer release slide downwards to open the trimmer (Fig. 10).
2 Switch on the appliance.
3 You can now start trimming.
4 Clean the trimmer after use (see ‚Cleaning the trimmer
(AT621, AT620 only)'). 5 Close the trimmer (Fig. 11).

Cleaning and maintenance

Cleaning the shaver under the tap
Clean the shaver after every shave for optimal performance. For the
best cleaning results, we advise you to use Philips Cleaning spray
(HQ110). Always unplug and switch off the shaver before you clean it.
Note: Water may leak from the socket at the bottom of the shaver
when you rinse it. This is normal and not dangerous because all
electronics are enclosed in a sealed power unit inside the shaver.
Caution: Be careful with hot water. Always check if the water is not
too hot, to prevent burning your hands.
Caution: Never dry the shaving unit with a towel or tissue, as this
may damage the shaving heads.
1 Place you thumb under the shaving unit and push the shaving unit
off the shaver (Fig. 12).
Note: Make sure to hold the shaving unit while doing so.
2 Rinse the hair chamber under the tap (Fig. 13).
3 Rinse the inside of the shaving unit under a hot tap.
4 Rinse the outside of the shaving unit under a hot tap.
Thorough cleaning
5 Turn the lock anticlockwise (1) and remove the retaining frame (2)
from the shaving unit (Fig. 16).
6 Remove and clean one shaving head at a time (Fig. 17). Each
shaving head consists of a cutter and a guard.
Note: Do not clean more than one cutter and guard at a time, since
they are all matching sets. If you accidentally mix up the cutters
and guards, it may take several weeks before optimal shaving
performance is restored.
7 Remove the cutter from the shaving guard and rinse it with water
(Fig. 18).
8 Rinse the inside and outside of the shaving guard with water (Fig. 19).
9 Put the shaving heads back into the shaving unit (Fig. 20). Make sure
that the projections of the shaving heads fit exactly into the recesses.
10 Put the retaining frame back into the shaving unit (1) and turn the
lock clockwise (2) (Fig. 21).
11 Reattach the shaving unit (Fig. 22).
Note: If you cannot reattach the shaving unit properly, check if you
have inserted the shaving heads properly and if the retaining frame
is locked.
12 Carefully shake off excess water, open the shaving unit again and
leave it open to let the shaving unit dry completely.
Caution: Be careful not to hit the shaving unit against anything while
you shake excess water off the shaver.
Cleaning the trimmer (AT621, AT620 only)
Clean the trimmer every time you have used it.
1 Switch off the shaver.
2 Push the trimmer release slide downwards to open the trimmer (Fig. 10).
3 Rinse the trimmer under a hot tap (Fig. 23).
4 Close the trimmer (' click') (Fig. 11).
Tip: For optimal trimming performance, lubricate the trimmer teeth
with a drop of sewing machine oil every six months (Fig. 24).
Replacement
For maximum shaving performance, we advise you to replace the
shaving heads every two years (Fig. 25). Replace damaged shaving
heads immediately. Always replace the shaving heads with original
Philips shaving heads as specified in the chapter ‚Ordering accessories'.
1 Switch off the shaver. Disconnect the shaver from the mains.
2 Place your thumb under the shaving unit and push the shaving unit
off the shaver (Fig. 12).
Note: Make sure to hold the shaving unit while doing so.
3 Turn the lock anticlockwise (1) and remove the retaining frame (2)
(Fig. 16).
4 Remove the shaving heads and place new ones in the shaving unit.
Make sure that the projections of the shaving heads fit exactly into
the recesses.
5 Put the retaining frame back into the shaving unit (1) and turn the
lock clockwise (2) (Fig. 21).
6 Reattach the shaving unit (Fig. 22).
Note: If you cannot reattach the shaving unit properly, check if you
have inserted the shaving heads properly and if the retaining frame
is locked

Ordering accessories

To buy accessories or spare parts, visit www.shop.philips.com/service
or go to your Philips dealer. You can also contact the Philips Consumer
Care Centre in your country (see the worldwide guarantee leaflet for
contact details).
The following accessories and spare parts are available:
-
HQ56 Philips shaving heads
-
HQ110 Philips shaving head cleaning spray
Note: Availability of the accessories may differ by country.
Recycling
-
Do not throw away the product with the normal household waste
at the end of its life, but hand it in at an official collection point for
recycling. By doing this, you help to preserve the environment.

Guarantee and support

If you need information or support, please visit www.philips.com/
support or read the separate worldwide guarantee leaflet.
Guarantee restrictions
The shaving heads (cutters and guards) are not covered by the terms of
the international guarantee because they are subject to wear.

Troubleshooting

This chapter summarizes the most common problems you could encounter
with the appliance. If you are unable to solve the problem with the
information below, visit www.philips.com/support for a list of frequently
asked questions or contact the Consumer Care Center in your country.
Problem Possible cause
The shaver does The shaving heads
not shave as well are damaged or
as it used to. worn.
Foam or gel
residues clog up the
shaving heads.
You have not
inserted the shaving
heads properly.
The shaver does The rechargeable
not work when I battery is empty.
press the on/off
button.
The temperature
of the shaver is too
high. In this case,
the shaver does not
work.
The shaver does This shaver is not
not work, although designed to be
it is connected to used directly from
the mains. the mains.
Solution
Replace the shaving heads
(see 'Replacement').
Rinse the shaving unit under
a hot tap (see 'Cleaning the
shaver under the tap').
Make sure that the
projections of the shaving
heads fit exactly into the
recesses.
Recharge the battery
(see 'Charging').
As soon as the temperature
of the shaver has dropped
sufficiently, you can switch
on the shaver again.
Recharge the battery (see
'Charging') and disconnect
the shaver from the mains.