Remote Controls And Accessories; Generator Maintenance - Cebora SOUND AC-DC 2330/M Manual De Instrucciones

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 37
4.4 SC (START-UP CURRENT).
Always active in all TIG processes.
Start current level where the welding process begins.
Especially used for AC starts-up with big electrodes and
slope up.
Sets the pedal minimum level - Art. 193
Default 25%.
Range: minimum 1% - maximum 100%
4.5- CRA (FINAL CRATER FILLER).
Select abbreviation CrA on display U by means of button
AQ, display O shows abbreviation OFF by means of knob
AA set ON to activate the function.
Press shortly button AQ to select abbreviation CrC.
4.5.1 CrC (Carter current)
This current is a percentage of the welding current and
the process final current.
Default 50%
Range:
minimum 10%
maximum 100%
4.5.2 tCr (Carter current time)
Crater current time duration.
Default 0.5 sec.
Range:
minimum 0.0 sec.
maximum 30 sec.
Functions visible in MMA process only.
4.6 HS (PERCENTAGE OF HOT-START CURRENT)
It is an overvoltage used to improve start-up.
Default 50%
Range:
minimum 0%
maximum 100%
4.7T HS (DURATION OF HOT-START CURRENT)
Default 0.15 sec.
Range:
minimum 0 sec.
maximum 0.5 sec.
4.8 AF (PERCENTAGE OF ARC-FORCE CURRENT)
It is a current that allows the electrode transfer.
Default 30%
Range:
minimum 0%
maximum 100%
18

5 REMOTE CONTROLS AND ACCESSORIES

The following remote controls may be connected to ad-
just the welding current for this welding machine:
Art. 193
Pedal control (used in TIG welding)
Art. 1260
BINZEL "ABITIG 200" Torch (200A-35%) m.4
Art. 1262
BINZEL "ABITIG 200"Torch Up/Down (200A
– 35%) – m. 4
Art. 1256
Water cooled torch BINZEL "ABITIG 450
W"
(450A) – m. 4
Art. 1258
Water cooled BINZEL torch "ABITIG 450 W
Up/Down" (450A) – m. 4
Art. 1656
Power source carriage
Art. 1281.03 Accessory for electrode welding
Art. 1341
Cooling unit
Art. 1192
Art 187 (used in MMA welding)
Art. 1180
Connector to connect torch and pedal
control at the same time.
Art 193 may be used in any TIG welding
mode with this accessory.
Controls
that include a potentiometer adjust the
welding current from the minimum to the maximum
current setting by means of knob AA.
Controls with UP/DOWN logic control welding cur-
rent from the minimum to the maximum value.
6 MAINTENANCE
Any maintenance operation must be carried out by qua-
lified personnel in compliance with standard CEI 26-29
(IEC 60974-4).

6.1 GENERATOR MAINTENANCE

In the case of maintenance inside the machine, make
sure that the switch BE is in position "O" and that the
power cord is disconnected from the mains.
It is also necessary to periodically clean the interior of the
machine from the accumulated metal dust, using com-
pressed air.
6.2
PRECAUTIONS AFTER REPAIRS.
After making repairs, take care to organize the wiring so
that there is secure insulation between the primary and
secondary sides of the machine. Do not allow the wires
to come into contact with moving parts or those that heat
up during operation. Reassemble all clamps as they were
on the original machine, to prevent a connection from
occurring between the primary and secondary circuits
should a wire accidentally break or be disconnected.
Also mount the screws with geared washers as on the
original machine.
Tabla de contenido
loading

Este manual también es adecuado para:

365

Tabla de contenido