Tig Welding; Remote Controls And Accessories; General Notes - Cebora AC-DC 1531/M Manual De Instrucciones

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 26
AB - Negative output terminal (-)
AC -Positive output terminal (+)
AF
AF - switch
Turns the machine on and off
AG - gas intake fitting
3.3.

GENERAL NOTES

Before using this welding machine, carefully read the stan-
dards CEI 26-23 / IEC-TS 62081. Also make sure the insula-
tion of the cables, electrode clamps, sockets and plugs are
intact, and that the size and length of the welding cables are
compatible with the current used.
3.4
MMA WELDING (MANUAL METAL ARC)
- Make sure that the switch AF is in position 0, then connect
the welding cables, observing the polarity required by the
manufacturer of the electrodes you will be using; also con-
nect the clamp of the ground cable to the workpiece, as
12
close to the weld as possible, making sure that there is good
electrical contact.
- Do NOT touch the electrode clamp simultaneously with the
earth clamp.
- Turn the machine on using the switch AF.
- Select the MMA procedure by pressing the button A:
LED B lit.
- Adjust the current based on the diameter of the electrode,
the welding position and the type of joint to be made.
- Always remember to shut off the machine and remove
the electrode from the clamp after welding.
3.5

TIG WELDING

By selecting TIG AC welding mode
aluminium, aluminium alloys, brass and magnesium, while
selecting TIG DC
iron and copper.
Connect the earth cable connector to the positive pole (+) of
the welding machine, and the clamp to the workpiece as
close as possible to the welding point, making sure there is
good electrical contact.
Connect the power connector of the TIG torch to the nega-
tive pole (-) of the welding machine.
Connect the torch connector to the welding machine con-
nector AE.
Connect the torch gas hose fitting to the fitting AD on the
machine, and the gas hose from the cylinder pressure regu-
lator to the gas fitting AG on the rear panel.
Turn on the machine.
Do not touch live parts and output terminals while the machi-
ne is powered.
The first time the machine is turned on, select the process
and mode using the push-buttons A and E, and the welding
AG
parameters by means of the key P and the knob AA as
described in paragraph 3.2.
The type and diameter of the electrode to be used must be
selected according to table A:
The flow of inert gas must be set to a value (in liters per
minute) approximately 6 times the diameter of the electrode.
If you are using gas-lens type accessories, the gas through-
put may be reduced to approximately 3 times the diameter
of the electrode. The diameter of the ceramic nozzle must be
4 to 6 times the diameter of the electrode.
Use D.I.N. 10 protective glasses for up to 75A, and D.I.N. 11
from 75A up.

4 REMOTE CONTROLS AND ACCESSORIES

The following remote controls may be connected to adjust
the welding current for this welding machine:
Art. 193
Foot control (used in TIG welding)
Art. 1260
BINZEL "ABITIG 200" Torch (200A – 35%) – m4
Art. 1262
BINZEL "ABITIG 200" Up/Down Torch (200A –
35%) – m4
Art. 1656
Power source trolley
Art. 1281.03 Accessory for MMA welding
Art 1192+Art 187 (used in MMA welding)
ART. 1180 Connection to simultaneously connect the torch
and the pedal control.
ART. 193
may be used in any TIG welding mode with this
accessory.
Remote controls that include a potentiometer regulate
you may weld
allows you to weld stainless steel,
12
Tabla de contenido
loading

Este manual también es adecuado para:

364

Tabla de contenido