Tabla de contenido
Anleitung_TE_RH_20_SPK8__ 15.06.16 08:18 Seite 17
e) Avoid abnormal working postures. Make sure
you stand squarely and keep your balance at
all times. In this way, you can control the electric
tool better in unexpected circumstances.
f)
Wear suitable work clothes. Do not wear
loose clothing or jewellery. Keep hair, clothes
and gloves away from moving parts. Loose
clothing, jewellery or long hair can get trapped in
moving parts.
g) If vacuuming devices and draining devices
can be fitted, make sure that these are
correctly attached and correctly used. The
use of a dust extraction system can reduce the
danger posed by dust.
Do not lose this safety information.
4. Usage and treatment of the electric tool
a) Do not overload the appliance. Use the
correct tool for your work. You will be able to
work better and more safely within the given
performance boundaries.
b) Do not use an electric tool with a defective
switch. An electric tool that cannot be switched
on or off is dangerous and must be repaired.
c) Pull the plug out of the socket and/or remove
the battery before making any adjustments to
the appliance, changing accessories or put
the appliance down. This safety measure
prevents starting the electric tool unintentionally.
d) Keep unused electric tools out of the reach of
children. Do not allow people who are not
familiar with the appliance or who have not
read these instructions to use the appliance.
Electric tools are dangerous if they are used by
inexperienced people.
e) Clean your electric tool carefully. Check
whether moving parts are functioning
properly and not jamming, whether parts are
broken or damaged
enough that the functioning of this electric
tool is affected. Have damaged parts repaired
before using the appliance. Many accidents
are caused by badly maintained electric tools.
f)
Keep your cutting tools sharp and clean.
Carefully maintained cutting tools with sharp
cutting edges will jam less and are easier to
control.
g) Make sure to use electric tools, accessories,
attachments, etc. in accordance with these
instructions. Take the conditions in your work
area and the job in hand into account. Using
electric tools for any purpose other than the one
for which they are intended can lead to
dangerous situations.
5. Service
a) Have your electric tool repaired only by
trained personnel using only genuine spare
parts. This will ensure that your electric tool
remains safe to use.
Do not lose these safety instructions
Safety Information for hammer
a) Wear ear protection. The impact of noise can
cause damage to hearing.
b) Use the additional handles supplied with the
tool. Losing control of the tool can cause
injuries.
c) Hold the equipment by the insulated handles
when carrying out work during which the
plug-in tool could strike concealed power
cables or its own mains lead. Contact with a
live cable can also make the metal parts of the
equipment live and will cause an electric shock.
Additional Safety rules
Check that your mains voltage is the same as
n
that marked on the rating plate.
If you use a cable reel, run all the cable off the
n
reel. The minimum conductor cross section used
should be 1.5 mm2.
If you use this electric hammer drill outdoors you
n
must connect it using a suitable H07RN-F 3G 1.5
mm2 extension cable with a spray-water
protected plug.
Make sure of your footing, particularly when
n
working free-handed on ladders or scaffolding.
Use a detector to localize pipes and/or cables in
n
walls with concealed electric, water or gas lines.
Avoid any contact with conducting electrical parts
or lines.
Wear ear-muffs to protect your hearing: Risk of
n
progressive loss of hearing!
Wear goggles and use a breathing mask on
n
dusty jobs.
Never use the machine near vapors or
n
combustible liquids.
Always unplug the machine before cleaning it or
n
changing drill bits etc.
Keep the power cable safe from damage. Oil and
n
acids can damage cables.
Never overload the machine.
n
Important! Follow all safety regulations in your
n
country applicable to the installation, use and
maintenance of the machine.
Chisel bits and drill bits can be inadvertently
n
thrown out from the machine and cause serious
injury:
GB
17
Tabla de contenido
