Battery Removal/Installation; Before Use - HIKOKI N 14DSL Instrucciones De Manejo

English
APPLICATION
○ Securing the moisture-permeable waterproofi ng sheet
in position
○ Securing the heat insulation material in position

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch to
remove the battery (Fig. 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (Fig. 2).
CHARGING
Battery and battery charger are not included with this
product.
For rechargeable batteries, please charge in according
to the handling instructions of the charger which you are
using. (Fig. 3)

BEFORE USE

1. Preparing the Staples and Performing Safety
Inspections
WARNING
○ Do not use the product near fl ammable liquids or
gases.
○ Do not place the product near children or other non-
qualifi ed people.
○ Run a full check to make sure that no screws are loose.
○ Check to make sure that there are no damaged or
missing parts, or malfunctioning parts owing to rust,
etc.
Prepare staples that match the job at hand.
Refer to MAINTENANCE AND INSPECTION and carry
out safety inspections without fail.
2. Trigger Lock Mechanism (Fig. 4)
WARNING
Make sure the trigger is locked when not fi ring staples.
This stapler has a lock mechanism to prevent the
staples from being fi red.
Set the lock lever at the
Slide the lock lever to the
to be used, and to the
3. Checking Push Lever Operations (Fig. 5)
WARNING
Always make sure the trigger is locked and the battery
removed from the power tool when checking push lever
operations.
Check to make sure the push lever slides smoothly
when operated.
Clean the sliding area on the push lever if it doesn't
slide smoothly.
4. Handling the Staples
NOTE
○ Handle the staples carefully.
There are cases in which the joined staple strips may
be broken if they are dropped, and using them in this
state may result in defective staple loading, leading
to blank fi ring or staple jams. Do not use joined staple
strips that are broken.
position to lock the trigger.
position when the stapler is
position when it is not in use.
○ Do not leave the staples outdoors or in direct sunlight
for long periods of time.
Failure to observe this may result in rusting or defects
in the joined staple strips. Use the staple packaging or
other materials for storage purposes.
5. Loading the Staples (Fig. 6)
WARNING
Lock the trigger and remove the battery from the
stapler when loading or removing staples.
(1) Press the stop lever and slide the magazine backward.
(2) Place the staples in the magazine with the prongs
facing upward.
(3) Slide the magazine back into position until the stop
lever locks into place.
NOTE
○ Close the magazine gently.
Using excessive force to close the magazine may result
in the joined staple strips being deformed, preventing
the magazine from being closed.
○ Check the magazine blade guide if it won't close
smoothly.
HOW TO USE THE CORDLESS
STAPLER
There are two ways to discharge staples: Single Shot, in
which the push lever is placed against the area where the
staple is to be fi red fi rst and the trigger then pulled, and
Continual Shot, in which the trigger is pulled fi rst and the
push lever then placed against the relevant area.
The single-shot mode places the emphasis on fi nishing
and is used to ensure that the staple is driven into the
required place, while the continual-shot mode is used to
drive in staples repeatedly with the trigger constantly being
pulled.
The power tool is equipped with a mechanism to alternate
between single-shot and continual-shot operations to
ensure that work is carried out in the most effi cient way.
Safety Devices
The power tool has been designed so that staples
cannot be fi red unless both the push lever and the
trigger are simultaneously operated. In other words,
staples will not be discharged when only the trigger is
pulled, or when only the push lever (discharge outlet)
is placed against the required area. This is to prevent
the staples from being discharged when the trigger is
accidentally pulled or when the push lever (discharge
outlet) is accidently placed against something.
● Single-shot Stapling (Fig. 7)
(1) Make sure the discharge outlet is fi rmly placed against
the place where the staple is to be discharged.
(2) Pull the trigger to fi re the staple.
(3) Withdraw the power tool and release the trigger.
NOTE
○ Use the single-shot mode to accurately staple the
required location.
○ There are cases in which subsequent stapling will not
be possible if the trigger is released halfway through
being pulled.
To correct this, remove the battery and then replace it.
● Continual-shot Stapling (Fig. 8)
First pull the trigger then place the push lever (discharge
outlet) against the required area to repeatedly fi re
staples.
(1) First pull the trigger.
(2) Place the push lever (discharge outlet) against the
required area to fi re the staples.
(3) Withdraw the stapler with the trigger pressed, and
then repeat procedure from step (2) to repeatedly fi re
staples.
20