3- Understanding The System Tones; 4- How To Use The Wireless Keypad With Display - Honeywell Domonial Manual De Uso

3- Understanding the system tones

E
N
SIRENS
G
A siren is an effective deterrent due to its power and very irritating tone.
L
The system has a siren built in the control panel. An optional remote siren
can be added.
I
In addition, the panel built-in siren emits an audible confirmation
S
tone when arming and disarming the security system and a fire tone
when a smoke detector is triggered. The volume levels can be adjus-
H
ted by the installer.
SYSTEM TONES
Sequence of 3 modulated sounds
TOTAL SET
ARMING
Duration : 4 seconds
PART SET
Sequence of 2 modulated sounds
ARMING
ANNEX SET
Duration : 2,5 seconds
ARMING
Upon arming...
EXIT DELAY
one beep every second
Upon entry...
ENTRY DELAY
one beep every second
Long and continuous beep
DISARMING
Duration : 2,5 seconds
2 times 7 fast beeps
FAULT
4 beeps in case of alert...
ALERT
sent via the keypad
When arming total set, confirms that
the control panel has received a valid
code or TAG and is preparing to arm
total set
When arming the part set, confirms that
the control panel has received a valid
code or TAG and is preparing to arm part
set
Beeps are played at the end of the exit
time until the system is armed.
After you open the entry door, the entry
time starts. You should disarm your
system within this time. Beeps are played
at the end of the entry time.
When Disarming, confirms that the
control panel has been successfully
disarmed
This tone indicates a fault in the system
Confirms the transmission of an alert to
the Alarm Receiving Centre
- 4 -

4- How to use the wireless keypad with display*

The wireless keypad with display offers a complete range of tools to manage
your alarm system, from normal operation to dedicated user functions.
The keypad is used to arm and disarm your security system using a valid
access code or key TAG. The master code or TAG is re q u i red to modify other
users' codes and TA G s .
ARMING USING YOUR CODE OR TA G
If the keypad is not in its base, please re t u rn it there (total or annex set).
• P ress an arming key on the keypad. If the system diagnoses a fault on
a rming, a fault message is displayed. Press the OK key or the arming key to
bypass the faults and continue the arming process.
• Enter a valid code or present a programmed TA G
- The arming tone is emitted by the keypad and by the panel sire n
(if setup).
- The screen counts down the exit time remaining.
- Arming is automatically completed at the end of the delay (Depends on
site configuration). The icon confirms the completion of setting.
The screen clears after a few seconds.
For total set arming, the keypad's left light indicator is on during the exit delay.
For part set arming, the keypad's right light indicator is flashing during the entire
set period.
DISARMING USING YOUR CODE OR TA G
To enable you to get to the keypad without triggering an alarm, your installer
has programmed an entry delay of 30 seconds (Depends on site configuration).
• Enter a valid code or present a programmed TA G
- The disarming tone is emitted by the keypad and by the panel sire n
(if set up).
D i s a rming the system will also stop the sirens if an alarm is triggered. Stopping
the siren does not interrupt the transmission of the alarm to the ARC.
Note : Depending on your keypad's configuration, this will disarm the total set or
the entire system. In the latter case, the annex set might need to be re-armed.
* The system may include 0 to 4 keypads of this type
Total set arming
Part set arming
4 or 6-digit code
4 or 6-digit code
- 5 -
E
N
G
L
I
S
H
TAG