Idiomas disponibles
Idiomas disponibles
Fig. 35
- Glue the former R 13 to the nose of the fuselage as
shown.
- Install the motor mounts R 14 and the motor bulkhead R
15.
- Glue the in-fill blocks R 16 on both sides.
Fig. 36
- Glue the nose former R 17 in place as shown; ensure that
the holes for the motor retaining screws in the ply
bulkhead remain accessible.
Fig. 37
- Glue together the wing retainer plate R 18 and the doubler
R 18a with their edges flush.
- Glue the wing retainer plate R 18 to the fuselage together
with the reinforcements T 19.
Fig. 38
- Install the fuselage formers R 0 and R 1 "dry" (no glue),
pulling the fuselage sides in to meet at the tail. Check that
Assembling the model, receiving system and electric power system, final work
Part
Description
No.
RC 4
Servo
RC 5
Servo output lever
RC 6
Pushrod
RC 7
Guide tube
RC 8
Aileron pushrod
RC 9
Captive nut
RC 10
Plastic screw
RC 11
Main undercarriage unit
RC 1
Wheel
RC 13
Collet and grubscrew
RC 14
Sleeve
RC 15
Brushless motor
RC 16
Socket-head cap screw
RC 17
Shakeproof washer
RC 18
Propeller driver
RC 19
Propeller
RC 0
Brushless speed controller
RC 1
Receiver
RC
Flight battery
Assembly and operating instructions
Charterle
the fuselage remains symmetrical when viewed from
above.
- Glue the tail end of the fuselage sides together.
- Glue the formers R 0 and R 1 to the fuselage sides.
Fig. 39
- Glue the fuselage turtle deck sheeting panels R and R
3 in place, checking constantly that the fuselage remains
straight: check this over the plan.
Figs. 40 and 41
- Glue the bottom fuselage sheeting panels R 4, R 5, R
6 and R 7 together as shown.
Fig. 42
- Glue the assembled bottom sheeting to the fuselage.
Fig. 43
- Glue the windscreen frame R 8 and the nose sheeting
panel R 9 to the fuselage.
Material
---
---
Steel wire
Plastic
Steel wire
Steel
---
Steel wire
Plastic
Brass / steel
Brass
---
Steel
Steel
Aluminium
Plastic
---
---
---
Dimensions
No. off
Ready made
, N.I.
Ready made
, with RC 4
0.8 Ø x 360
300 long
0.8 Ø x 55
M4
1
M4 x 5
1
Ø x 50
1
51 Ø
. Ø x 7 Ø x 5
4
. Ø x 3 Ø x 14
Ready made
1, N.I.
M x 5
Ø x 4.3 Ø
Ready made
1, N.I.
8 x 3.8"
1, N.I.
Ready made
1, N.I.
Ready made
1, N.I.
Ready made
1, N.I.
8
Figs. 44 and 45
- Assemble the battery hatch from parts R 30 and R 31 and
trim it to fit on the fuselage.
Fig. 46
- Round off the fuselage nose as shown in the photo.
Figs. 47 and 48
- The entire fuselage can now be rounded off.
Fig. 49
- Glue the plastic latch to the underside of the hatch, taking
care to keep it central.
Note: the pushrod support R 3 and the tailskid R 33 are
not fitted until the model has been covered. The main
undercarriage should also be installed after covering is
complete.
Fig. 50
- Place the hatch on the fuselage and check that the latch
works correctly; you may need to make minor adjust-
ments to the hole in the former R 13.
No.
3279
