Handle Adjustment - Chicco Urban Instrucciones De Uso

TRANSFORMING THE SEAT INTO THE PRAM
WARNING: This product is only suitable
for children who are not able to sit upright,
turn around or pull themselves onto their
hands and knees without assistance.
Maximum weight of the child: 9 Kg.
To transform the seat into a pram, follow the steps below:
14. Unfasten the buckles located under the seat (fig. 14 – 14A).
15. Position the foot rest horizontally, adjust the back rest in the
lowest position (fig. 15), recline the seat by pressing the buttons
shown in fig. 11, and bring the pram into the horizontal position
(fig. 15A).
WARNING:The pram must be used only
in horizontal position (fig. 16A). Do not
adjust the pram in the reclined positions
(Fig 16B, Fig 16C).
16. Remove the safety belts (see paragraph REMOVE SAFETY
BELTS), making sure to store them away out of the reach of your
child.
17. Introduce the padded mattress: to introduce the mattress,
fasten it to the fabric component of the stroller by using the
internal zip (fig. 17) positioned in the child's head area.
18. Then wrap the elastic part of the mattress around the tube of
the structure in the foot area (fig. 18). Lastly, fasten the press stud
buttons positioned on both sides (fig. 18A).
WARNING: The pram should be used from
birth up to 6 months of age
WARNING: When the seat is in the pram
configuration, it should be fitted onto the
stroller facing the parent (Fig. 18B-18C).
WARNING: Do not remove the pram from
the stroller when the child is inside of it.
USE OF THE SAFETY BELTS
The stroller is equipped with a retaining system with five anchoring
points, consisting of two shoulder straps, two adjusting slots, a
waist belt and a crotch strap with buckle, already assembled.
WARNING: to adapt the belts to the body of the child, use the
shoulder straps, passing them through the two regulation holes as
indicated in Fig. 19.
19. After laying the child in the stroller, fasten the belts by
threading first the two forks inside the shoulder straps' slot (fig.
19A) and then introduce them inside the crotch strap buckle (fig.
19B); adjust the length of the belts, making sure they adhere to
your child's shoulders and body. To unfasten the waist belt press
and pull the lateral forks (fig. 19C).
WARNING: Always use the restraint
systems. For the safety of your child use
all five fixing points of the safety harness
belts.
WARNING: To ensure the safety of your
child, use the safety belts at all times.
20. For further safety, the stroller is equipped with ''D''-shaped
rings to allow hooking an additional safety belt, compliant with BS
6684 standard. The rings are located inside the stroller's seat on
the right and left side, as shown in (fig. 20).
REMOVING THE SAFETY BELTS
The safety belts can be removed (to be washed or used in pram
configuration).
21. To remove the belts, unfasten the waist belt from the relative
''D''-shaped rings and the shoulder straps from the fabric slots
located on the backrest.
After removing the safety belts, make sure that the belts are re-
assembled properly using the anchoring points.
To re-assemble the safety belts systems, follow the sequence
below carefully:
22. Pass the belt through the slot as shown in (fig. 21), making sure
that the length adjuster is positioned as shown in (fig. 22).
23. Take the plastic slot end of the shoulder strap and introduce it
into the safety belt's fabric ring (Fig. 23).
24. After performing this operation properly, pull the belt
downward until the fabric ring is turned inside out (fig. 24A-24B).
25. WARNING: At the end of the assembly, make sure that the
plastic slots are properly assembled. Check that the plastic slots,
once assembled on the relative safety harness buckle forks, feature
the relative horizontal protruding parts facing the seat's exterior
(fig. 25A-25B).
At the end of the assembly, the belts must be adjusted once again
according to the size of your child.
PARKING BRAKE
The stroller is equipped with pedal parking brake located on the
rear axle.
26. To engage the parking brake, press the pedal downward with
one foot (fig. 26).
27. To disengage the parking brake, push the pedal upward (fig.
27).
WARNING: Always use the brake when not moving. Never leave
the stroller on a sloping surface with your child inside it, even if the
parking brake is engaged.
WARNING: After engaging the parking brake, make sure the
brakes are properly enabled on both rear wheels.
SWIVEL WHEELS
The stroller is equipped with front swivel/fixed wheels.
28. It is suggested to use the fixed wheels on particularly uneven
grounds. The wheels in swivel mode instead, can be used to
improve the stroller's handling on regular road surfaces.
To engage the front swivel wheels, push the front button
downward with your foot as shown in fig. 28.
To engage the front fixed wheels, press again the button with your
foot. Regardless of the position in which the wheel is located, they
will lock in straight position.
WARNING: Both wheels must always be locked or released to
swivel at the same time.

HANDLE ADJUSTMENT

The stroller features a handle that can be adjusted in height,
according to the user's needs.
29. It can be adjusted in 4 different positions by pressing the
release button located at the centre of the handle (fig. 29).
After switching from one position to the other, make sure the
automatic locking mechanism is properly engaged.
REMOVABLE BUMPER BAR
The stroller is equipped with removable bumper bar.
30. To remove it, press the buttons located on the sides (fig. 30).
31. To position and remove the child, unhook the bar from one
side only (fig. 31).
WARNING: Always fasten the safety belts. The bar IS NOT a
device to retain the child.
WARNING: The bar must not be used to lift the product with the
child inside of it.
24