Cleaning The Filters - Hoover CP71CP01 Manual De Instrucciones

GETTING TO kNOw yOUR ClEANER
A. Main Cleaner
B. Cord Rewind Pedal
C. Carry Handle
D. Exhaust Filter Cover
E. On/Off Pedal
F. Telescopic Tube*
G. Telescopic Tube Release Button*
H. standard Tube*
I. Variable Power Control Roller*
J. Bag Check Indicator
K.
Bag Door Release Latch
L. suction Regulator*
M. Handle
ASSEmBlING yOUR ClEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it clips and locks into position. To
release: simply press the two buttons on the hose end and pull [2].
2. Connect the tube upper end to the handle. [3].
3. Connect the tube lower end to the carpet and floor nozzle [4].
USING yOUR ClEANER
1. Extract power cord and plug it into the power supply. Do not pull the cord beyond the red
marker [5].
2. Adjust the length of the telescopic tube* by moving the telescopic release button* up and
raise or lower the handle to the most comfortable cleaning position [6].
3. Carpet & Floor Nozzle. Press the pedal on the nozzle [7] to select the ideal cleaning mode
for the floor type.
Hard Floor: The brushes are lowered to protect the floor
Carpet: With lifted brushes for the deepest clean
4. switch the cleaner on by pressing the On/Off pedal on the cleaner main body. [8]
5. Adjust the power level by rotating the variable power control roller*. [9]
6. Adjust the suction regulator* to the desired level. [10].
7. switch off at the end of use by pressing the On/Off pedal. Unplug and press the cord rewind
pedal to wind the power cord back into the cleaner [11].
8. Parking and storage - The tube can be parked for temporary storage while in use, or in the
storage position when not in use [12].
*Certain Models Only ** Certain models only, nozzles may vary according to model
N. Carpet and Floor nozzle(GP)**
N1. Carpet Nozzle (CA)**
N2. Hard Floor Nozzle (HF)**
O. surface selector Peda **
P. Hose
Q. Pre motor filter
R. Exhaust filter
s. 2 in 1 Tool
T. Pet Hair Remover Mini Turbo Nozzle*
U. Allergen Remover Mini Turbo Nozzle*
V. Grand Turbo Nozzle*
W. Parquet nozzle*
ClEANER mAINTENANCE
Replacing The Dust Bag
If the bag check indicator is red please check and, if necessary, replace the bag.
1. Lift the bag door release latch [13] to open the cover, pull the bag holder [14] and pull the
bag collar to remove the bag [15].
2. Apply the peel and seal sticker, located on the bag collar, to the bag inlet. The full dust bag
should be disposed of correctly and carefully.
3. Fold a new bag as shown on the bag and fit by inserting the collar into the bag holder.
4. Refit the bag holder and close the bag door.
warning - The bag door will NOT close if the dust bag and/or the bag holder are not assembled
to the cleaner. Always ensure the bag and bag holder are present when closing the bag door.
Remember: The bag check indicator may also be red if an obstruction has occurred. In this
case refer to 'Removing A Blockage From the system' .

Cleaning the Filters

To maintain optimum performance of your cleaner, please wash the filters after each 5 bag changes.
Cleaning the pre-motor filter:
1. Lift the bag door release latch [13] to open the cover and remove the bag holder.
2. To remove the pre-motor filter slide the pre-motor filter frame from the cleaner. [16]
3. Remove the filter from the holder. [17]
4. Wash it in hand warm water, [20] and allow it to dry thoroughly before replacing to the
cleaner [21].
Cleaning the exhaust filter:
1. To remove the exhaust filter, unclip the exhaust filter cover [18] and remove the filter pack. [19]
2. Wash the filter in hand warm water [20] and allow it to dry thoroughly before replacing to
the cleaner. [21].
Remember: Do not use hot water or detergents. In the unlikely event of the filters becoming
damaged, fit a Genuine Hoover replacement. Do not try and use the product without a dust
bag or filter fitted.
Cleaning the permanent cloth dust bag*
To maintain optimum performance we recommend that you wash the permanent cloth dust
bag under hand warm water after every 5 full bags. Remove excess water and leave to dry fully
before replacing.
Removing a Blockage From The System
If the bag check indicator is illuminated or flashing:
1. Check if the bag is full. If so refer to 'Replacing The Dust Bag' .
2. If it is not full, then;
A. Do the filters need cleaning? If so refer to 'Cleaning the Filter' .
B. Check if there is any other blockage in the system - Use a rod or a pole to remove any
blockage from the Teletube or flexible hose.
Warning - The bag check indicator will turn red if the cleaner is used when full, if there is a
blockage or if the filters are dirty. If the cleaner is used for a significant period of time with the
bag check indicator is red, a thermal cut out will switch the cleaner off to prevent overheating.
The bag check indicator turn green once the cleaner has switched off to signal that the thermal
cut out has been activated. If this should happen, switch the cleaner off, unplug and correct the
fault. It will take about 30 minutes for the cut out to automatically reset.
2
GB