Torque Settings; Protecting The Environment; Service Information - BLACK&DECKER CD121K Manual De Instrucciones

16 • ENGLISH

Torque Settings

► To set the tool's torque, rotate the adjustable torque collar
clockwise as required.
► The positions are marked around the collar and the higher
the number, the higher the torque.
► Each click in a clockwise direction means an increase in
the torque produced. Position 17 is the drill mode and is
marked with the picture of a drill bit. In this position the
clutch will not operate. This permits heavy duty drilling /
driving screws.
Keyless Chuck Operation
Double sleeve Chuck
► To attach accessories, grasp the rear half of the chuck
with one hand and use your other hand to rotate the front
half in the counterclockwise direction.
► Insert the bit or other accessory fully into the chuck, and
tighten secur ely by holding the rear half of the chuck and
rotating the front portion in the clockwise direction as
viewed from the chuck end.
DRILL
► Use sharp drill bits only.
► Support and secure work properly, as instructed in the
"Safety Instructions".
► Use appropriate and required safety equipment, as
instructed in the safety instructions.
► Secure and maintain work area, as instructed in the
safety instructions.
► Run the drill very slowly, using light pressure, until the
hole is started enough to keep the drill bit from slipping
out of it.
► Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
► Hold the drill firmly to control its twisting action.
► Do not click the trigger of a stalled drill off and on in an
attempt to start it. Damage to the drill can result.
► Minimize stalling on breakthrough by reducing pressure
and slowly drilling through last part of hole.
► Keep the motor running while pulling the bit out of a
drilled hole This will help reduce jamming.
► Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry.
Lubricants that work best are sulphurized cutting oil
or lard oil.
► Make sure switch turns drill on and off.
Warning! It is important to support work properly and to
hold the drill firmly to prevent loss of control which could cause
personal injury.
MANTENIMIENTO
Your tool has been designed to operate over a long period
of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off
and unplug the tool.
► Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
► Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
► Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment should be performed by
authorized service centers or other qualified service
organizations, always using identical replacement parts.

PROTECTING THE ENVIRONMENT

Separate collection. This product must not be
disposed of with normal household waste. Should
you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you,
do not dispose of it with household waste. Make this
product available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again. Re-use
of recycled materials helps prevent environmental
pollution and reduces the demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at municipal
waste sites or by the retailer when you purchase a
new product.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned
and authorized service locations. All Black & Decker Service
Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. For more
information about our authorized service centers and if you
need technical advice, repair, or genuine factory replacement
parts, contact the Black & Decker location nearest you,
or visit us at www.BlackandDecker-la.com
SPECIFICATIONS
Battery
Charger
Amps
B3
Charge time
CD121K CD961
12V 9,6V
JDA-14 JDA-12
400mA 400mA
5-7hr 5-7hr