Safety Notice - Poulan Pro PP5020AV Manual De Instrucciones

The following guide bar and chain combinations
meet kickback requirements of CSA Standards
Z62.1, Z62.3, & ANSI B175.1 when used on
saws listed in this manual. Use of bar and chain
Computed kickback angle (CKA) Table
MODEL
PP5020AV
NOTE:
To comply with Federal OSHA Regu-
lations for Commercial Logging, a chain brake
is required and shall not be removed or other-
wise disabled.

SAFETY NOTICE:

through prolonged use of gasoline powered hand
tools could cause blood vessel or nerve damage
in the fingers, hands, and joints of people prone
to circulation disorders or abnormal swellings.
Prolonged use in cold weather has been linked to
blood vessel damage in otherwise healthy
people. If symptoms occur such as numbness,
pain, loss of strength, change in skin color or
texture, or loss of feeling in the fingers, hands, or
joints, discontinue the use of this tool and seek
medical attention. An anti-vibration system does
not guarantee the avoidance of these problems.
Users who operate power tools on a continual
and regular basis must monitor closely their
physical condition and the condition of this tool.
SPECIAL NOTICE:
with a temperature limiting muffler and spark
arresting screen which meets the requirements of
California Codes 4442 and 4443. All U.S. forest
land and the states of California, Idaho, Maine,
Protective gloves (not provided) should be
worn during assembly.
NOTE: CHAIN BRAKE MUST BE
DISENGAGED BEFORE CLUTCH
COVER CAN BE REMOVED OR RE-
INSTALLED ON THE CHAIN SAW.
TO DISENGAGE CHAIN BRAKE,
PULL THE FRONT HAND GUARD
BACK TOWARD THE FRONT HAN-
DLE AS FAR AS POSSIBLE (SEE
ILLUSTRATION).
Disengaged
ATTACHING THE BUMPER SPIKE
(If not already attached)
The bumper spike may be used as a pivot when
making a cut.
1. Move ON/STOP switch to the STOP posi- tion.
2. Disengage chain brake.
3. Loosen and remove the chain brake nuts
and the clutch cover from the saw.
NOTE:
If clutch cover can not be easily re-
moved from the chain saw, ensure chain brake is
BAR
P/N
577179801
Exposure to vibrations
Your saw is equipped
ASSEMBLY
Engaged
combinations other than those listed is not rec-
ommended and may not meet the CKA require-
ments per standard.
Length CHAIN P/N
20"
577180501
Minnesota,
Washington require by law that many internal
combustion engines to be equipped with a spark
arresting screen. If you operate a chain saw in a
state or locale where such regulations exist, you
are legally responsible for maintaining the
operating condition of these parts. Failure to do so
is a violation of the law. Refer to the SERVICE
section for maintenance of the spark arresting
screen. Failure to follow all Safety Rules and
Precautions can result in serious injury.
situations occur which are not covered in this
manual, use care and good judgement. If you
need assistance, contact your authorized service
dealer or call 1-800- -554- -6723.
STANDARDS:
ance with:
ANSI B175.1- - 2012 American National
Standards for Gasoline- -Powered Chain
Saws - - Safety Requirements
CSA Z62.1- - 2011 Chain Saws - - Occupa-
tional Health and Safety
CSA Z62.3- - 2011 Chain Saw Kickback Oc-
cupational Health and Safety
disengaged by pulling the front hand guard back
toward the front handle as far as possible.
4. Attach the bumper spike with the two
screws as shown.
Clutch Cover
Bar
Nuts
ATTACHING THE BAR & CHAIN (If not
already attached)
WARNING:
peat all steps to ensure your saw is properly as-
sembled and all fasteners are secure. Always
wear gloves when handling the chain. The chain
is sharp and can cut you even when it is not mov-
ing!
1. Move ON/STOP switch to the STOP posi-
tion.
2. Disengage chain brake.
3. Loosen and remove the bar nuts and the
clutch cover from the saw.
6
CKA without chain brake
17_
New Jersey, Oregon,
This saw is tested in accord-
Bumper Spike
If received assembled, re-
and
If