HIKOKI CJ 110MV Instrucciones De Manejo página 4

English
STANDARD ACCESSORIES
In addition to the main unit (1), the package contains the
accessories listed in the below.
○ Blades (No. 41) .......................................................... 1
Refer to Table 1 for use of the blades.
○ Hexagon bar wrench ................................................... 1
○ Splinter guard ............................................................. 1
○ Dust collector .............................................................. 1
○ Chip cover ................................................................... 1
Standard accessories are subject to change without notice.
APPLICATIONS
○ Cutting various lumber and pocket cutting
○ Cutting mild steel plate, aluminum plate, and copper
plate
○ Cutting synthetic resins, such as phenol resin and vinyl
chloride
○ Cutting thin and soft construction materials
○ Cutting stainless steel plate (with No. 97 blade)
SPECIFICATIONS
Voltage (by areas) *
Power Input *
Max. cutting depth
No-load speed *
Stroke
Min. cutting radius
Weight (without cord) **
* Be sure to check the nameplate on product as it is subject
to change by areas.
**According to EPTA-Procedure 01/2014
NOTE
Due to HiKOKI's continuing program of research and
development, the specifications herein are subject to
change without prior notice.
(110 V, 115 V, 120 V, 127 V,
220 V, 230 V, 240 V)
720 W
Wood 110 mm
Mild steel 10 mm
850 ― 3000 min
-1
2.6 mm
25 mm
CJ110MV: 2.4 kg
CJ110MVA: 2.3 kg
MOUNTING AND OPERATION
Action
Changing blades
Adjusting the blade operating speed
Switch operation
Adjusting the orbital operation
Housing the hexagonal bar wrench
Splinter guard
Sub base
Chip cover
Lighting up the lamp
Rectilinear cutting
Cutting a circle or a circular arc
Cutting metallic materials
Angular cutting
Pocket cutting
Concerning cutting of stainless steel
plates*
Connecting with cleaner
Selecting accessories
*NOTE
○ Dial scale reading is for reference only. The higher the
speed is, the quicker the material is cut. But the service
life of the blade will be reduced in this case. When the
speed is too low, cutting will take longer, although the
service life will be prolonged. Make adjustments as
desired.
○ When cutting use cutting fluid (oil base cutting fluid) to
prolong the blade's service life.
SELECTION OF BLADES
Accessory blades
To ensure maximum operating efficiency and results, it is
very important to select the appropriate blade best suited to
the type and thickness of the material to be cut. The blade
number is engraved in the vicinity of the mounting portion
of each blade. Select appropriate blades by referring to
Table 1.
MAINTENANCE AND INSPECTION
1. Inspecting the blade
Continued use of a dull or damaged blade will result in
reduced cutting efficiency and may cause overloading of
the motor. Replace the blade with a new one as soon as
excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes
For your continued safety and electrical shock protection,
carbon brush inspection and replacement on this tool
should ONLY be performed by a HiKOKI AUTHORIZED
SERVICE CENTER.
4
Figure Page
1 110
2
110
3 110
4 111
5
111
6 111
7
111
8 111
9 112
10
112
11 112
12 112
13 113
14 113
15 113
16
113
― 114