Hitachi Koki DH 24DVA Instrucciones De Manejo página 8

English
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated
battery packs.
Use of any other battery packs may create a risk
of injury and fire.
c) When battery pack is not in use, keep it away from
other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool
is maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach of
children and infirm persons.
CORDLESS ROTARY HAMMER SAFETY WARNINGS
1. Wear ear protectors
Exposure to noise can cause hearing loss.
2. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. When using this unit continuously, the unit may
overheat, leading to damage in the motor and
switch. Please leave it without using it for
approximately 15 minutes.
SPECIFICATIONS
POWER TOOL
Model
No-load speed Save/Power
Full-load impact rate Save/Power
Drilling Steel
Capacity
Driving Wood screw
Rechargeable battery
Weight
Do not use the "SAVE" mode when boring holes with the wood drill. There is a likelihood that the motor
will burn out.
CHARGER
Model
Charging voltage
Weight
7
Concrete
Wood
4. When drilling in wall, floor or ceiling, check for
buried electric power cord, etc.
5. Bring the battery to the shop from which it was
purchased as soon as the post-charging battery
life becomes too short for practical use. Do not
dispose of the exhausted battery.
6. Do not touch the bit during or immediately after
operation. The bit becomes very hot during
operation and could cause serious burns.
7. Always hold the body handle and side handle of
the power tool firmly. Otherwise the counterforce
produced may result in inaccurate and even
dangerous operation.
8. Wear a dust mask
Do not inhale the harmful dusts generated in
drilling or chiseling operation. The dust can
endanger the health of yourself and bystanders.
9. Always charge the battery at a temperature of 0
– 40°C.
A temperature of less than 0°C will result in over
charging which is dangerous. The battery cannot
be charged at a temperature higher than 40°C.
The most suitable temperature for charging is that
of 20 – 25°C.
10. Do not use the charger continuously.
When one charging is completed, leave the charger
for about 15 minutes before the next charging of
battery.
11. Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
12. Never disassemble the rechargeable battery and
charger.
13. Never short-circuit the rechargeable battery. Short-
chircuiting the battery will cause a great electric
current and overheat. It results in burn or damage
to the battery.
14. Do not dispose of the battery in fire.
If the battery is burnt, it may explode.
15. Do not insert object into the air ventilation slots
of the charger.
Inserting metal objects or inflammables into the
charger air ventilation slots will result in electrical
shock hazard or damaged charger.
16. Using an exhausted battery will damage the charger.
DH24DVA
–1
0 – 520 min / 0 – 1050 min
–1
0 – 2200 min
24 mm
13 mm
30 mm
6.2 mm (diameter) × 40 mm (length)
EB2420: Ni-Cd 24 V (2.0 Ah 20 cells)
EB2430HA: Ni-MH 24 V (3.0 Ah 20 cells)
EB2433X: Ni-MH 24 V (3.3 Ah 20 cells)
4.1 kg
UC24YFB
24 V
0.6 kg
–1
–1
/ 0 – 4500 min