Bosch PCM 8 Manual Original página 21

OBJ_BUCH-2324-003.book Page 21 Wednesday, October 19, 2016 5:09 PM
14 Adjustable fence
15 Bevel lock lever
16 Laser beam outlet
17 Roller
18 Saw blade
19 Dust bag
20 Laser on/off switch (for marking of cutting line)
21 On/Off switch
22 Chip ejector
23 Mounting holes for material clamp
24 Hex key
25 Tilt-protector bar
26 Transport safety-lock
27 Material clamp
28 Spindle lock
29 Indicator for bevel angle
30 Scale for bevel angle
31 Fastening screw for insert plate
32 Fastening screw for tilt-protector bar
33 Hex socket screw for mounting of saw blade
34 Clamping flange
35 Interior clamping flange
36 Wing bolt
37 Threaded rod
38 Clamping lever of the adjustable fence
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Mitre Saw
Article number
Rated power input
No-load speed min
Laser type
Laser class
Divergence of laser line
Weight according to
EPTA-Procedure 01:2014
Protection class
Permissible workpiece dimensions (maximum/minimum) see page 24.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Max. cutting width
Mounting hole diameter
Bosch Power Tools
Noise Information
Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 96 dB(A); Sound power level
103 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards:
EN 61029-1, EN 61029-2-9, EN 60825-1,
EN 50581:2012.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
 Avoid unintentional starting of the machine. During as-
PCM 8
3 603 M10 0..
W 1200
Delivery Scope
-1
4800
nm 650
mW < 1
2
1.0 mrad (full angle)
low have been supplied:
– Mitre saw with mounted saw blade
kg 7.9
– Dust bag 19
/II
– Material clamp 27
– Hex key 24
– Tilt-protector bar 25 with fastening screws 32
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
mm 216
be carefully checked to ensure flawless operation of the tool.
mm 1.4–1.8
All parts must be properly mounted and all conditions fulfilled
mm 2 that ensure faultless operation.
Damaged protective devices and parts must be immediately
mm 30
replaced by an authorised service centre.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
Please also observe the representation of
the delivery scope at the beginning of the op-
erating instructions.
Before starting the operation of the machine
for the first time, check if all parts listed be-
English | 21
1 609 92A 1KT | (19.10.16)