Basic Operation; Turning On The Device - Korg MS-20FS Manual Del Usuario

Basic Operation

1. Connections
Make sure each device is turned off before connecting any add itional
equipment. If an operation is inadvertently performed, the speaker system
and other devices may be damaged or malfunction.
1. Connecting the AC adapter
Connect the included AC adapter to the DC12V jack.
Only use the included AC adapter.
2. Connecting the amp
Connect the powered monitor speaker or mixer to the SIGNAL
OUT jack.
3. Connecting headphones
When using headphones, insert the headphone plug into the
PHONES jack.
4. Connecting guitars and microphones to the SIGNAL IN jack
When using an external signal processor, connect the guitar or
microphone to the SIGNAL IN jack.
For details, refer to "Using the External Signal Processor (ESP)" in
the original Owner's Manual.

2. Turning on the device

1. Turn the VOLUME knob clockwise.
After a click, the STANDBY ON LED lights up and the device is
turned on.
TIP If the auto power off function is disabled, the LED blinks a few times.
2. To turn off the device, turn the VOLUME knob counterclockwise
until it clicks and the LED turns off.
TIP If the AC adapter is disconnected while the MS-20 FS is turned on or
if the auto power off function has been enabled, the device may have
turned off without the VOLUME knob in the off position. Before turn-
ing on the MS-20 FS again, you'll have to turn the VOLUME knob
counterclockwise to turn it off.
Auto power off function
The MS-20 FS is automatically turned off if none of the following opera-
tions are performed for 4 hours.
• Sound is produced with the keyboard; Note On via MIDI IN or USB
MIDI; input to TRIG IN
When turning on the MS-20 FS again, turn the VOLUME knob counterclock-
wise to turn it off, and then turn on the device.
TIP The auto power off function is enabled as a factory setting (default.)
To disable the auto power off function
While holding down C1, D1 and E1 on the keyboard, turn on the MS-20
FS.
After the STANDBY ON LED blinks a few times, it remains lit, and then
the device returns to normal operation.
TIP The setting for the auto power off function is saved, even if the MS-20 FS is
turned off.
When changing the setting, do not turn off the device before the STANDBY
ON LED lights up. Otherwise, data may be corrupted or the device may be
damaged.
To enable the auto power off function again
While holding down C1, D1 and F1 on the keyboard, turn on the MS-20
FS.
The STANDBY ON LED lights up, without blinking, and then the device
returns to normal operation.
4
powered monitor
speaker, mixer
3. Producing sounds
Basic settings
Refer to "Normal Setting" and adjust the knobs.
Producing sounds by playing the keyboard
Press a keyboard key to hear the tone.
To adjust the volume, turn the VOLUME knob.
TIP Even if multiple keyboard keys are pressed, only one tone will be produced.
When two or more keys are pressed, the highest tone played will be pro-
duced.
Adjusting the knobs
Turn the CUTOFF FREQUENCY knob of the LOWPASS FILTER coun-
terclockwise to round off the sound. In addition, adjust the timbre by
using the OSCILLATOR 1 knob to change the waveform to the triangle
wave.
Patching to add variations to timbre
Refer to the following illustration and connect the patch cables.
The control wheel and momentary switch can be used. Adjust the con-
trol wheel and momentary switchs, and listen to the variations in the
timbre.
Refer to the original Owner's Manual and the setting chart to create
various sounds.
VCF setting
The VCFs (high-pass filter & low-pass filter) of the original MS-20 are
differentiated into the earlier and later filters, depending on the produc-
tion date.
Since the circuitry of these two types of filters differs, they have different
sound quality characteristics, although their frequency characteristics
are similar.
The MS-20 FS is equipped with both types of filters for you to select as
desired.