Manufacturer's Warranty; Spare Parts Lists - REMS Akku-Amigo 22 V Instrucciones De Servicio

eng
4.1. Maintenance
WARNING
Pull out the mains plug or remove the battery before repair work!
The REMS reciprocating saws are maintenance-free. The gear runs in a life-
long grease fi lling and therefore needs no lubrication. Keep the saw blade
holder clean. Remove chips from the housing of the saw blade holder. Remove
water/moisture from the housing of the saw blade holder after every use. Lightly
lubricate the saw blade holder and saw blade clamping lever (14) with machine
oil (only REMS Puma VE). Change a defective locking screw (9) (except REMS
Puma VE). Clean plastic parts (e.g. housing, batteries) only with the REMS
CleanM (Art. No. 140119) or a mild soap and a damp cloth. Do not use house-
hold cleaners. These often contain chemicals which can damage the plastic
parts. Never use petrol, turpentine, thinner or similar products for cleaning.
Make sure that liquids never get inside the REMS reciprocating saw. Never
immerse the REMS reciprocating saw in liquid.
5. Faults
5.1. Fault: REMS reciprocating saw stops during sawing.
Cause:
● Feeding pressure too high.
● Blunt saw blade (5).
● Unsuitable saw blade (5).
● Overload protection (8) has activated (REMS Tiger ANC).
● Worn carbon brushes.
● Too low operating pressure (REMS Tiger ANC pneumatic).
● Too little air supplied by the compressor (REMS Tiger ANC pneumatic).
● Battery (13) depleted (REMS Akku-Cat ANC VE).
5.2. Fault: No right-angled cut when sawing pipes with guide holder (2).
Cause:
● Feeding pressure too high.
● Unsuitable saw blade (5).
● Blunt saw blade (5).
● Prism of the guide holder (2) soiled (chips!).
5.3. Fault: REMS reciprocating saw does not start.
Cause:
● Overload protection has activated (REMS Tiger ANC).
● Mains lead defective.
● Battery (13) depleted (REMS Akku-Cat ANC VE).
● REMS reciprocating saw defective.
5.4. Fault: Centring pin shears off, saw blade (5) cannot be clamped securely enough (REMS Tiger and REMS Cat all models).
Cause:
● Clamping screw (9) worn.
● Allen key worn (see 2.5.).
6. Disposal
REMS reciprocating saws, batteries and rapid chargers may not be thrown in
the household waste when they are fi nished with. They must be disposed of
properly by law. Lithium batteries and battery packs of all battery systems may
only be disposed of in the discharged state, all contacts of incompletely
discharged lithium batteries and battery packs must be covered with insulating
tape.

7. Manufacturer's Warranty

The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which REMS is not responsible, shall be excluded from the warranty
4.2. Inspection/Servicing
WARNING
Before any repair work, pull the mains plug or remove the battery! This
work may only be performed by qualifi ed personnel.
The REMS reciprocating saws with universal motor have carbon brushes.
These are subject to wear and must therefore by checked and changed by
qualifi ed specialists or an authorised REMS customer service workshop from
time to time. In the battery-operated drive units, the carbon brushes of the
motor are subject to wear. These cannot be replaced; the DC motor must be
replaced.
Remedy:
● Reduce feeding pressure.
● Change the saw blade.
● Choose a suitable saw blade (see 2.4. and Fig. 8).
● Wait a few seconds then press the button of the overload protection.
● Have the carbon brushes or DC motor changed by qualifi ed personnel or an
authorised REMS customer service workshop.
● Increase operating pressure. Select the compressor according to the technical
data 1.6.
● Select the compressor according to the technical data 1.6.
● Charge the battery with the Li-Ion/Ni-Cd rapid charger or change the battery.
Remedy:
● Reduce feeding pressure.
● Choose a suitable saw blade (see 2.4. and Fig. 8).
● Change the saw blade.
● Clean the prism.
Remedy:
● Wait a few seconds then press the button of the overload protection.
● Have the mains lead replaced by qualifi ed personnel or an authorised REMS
customer service workshop.
● Charge the battery with the Li-Ion/Ni-Cd rapid charger or change the battery.
● Have the REMS reciprocating saw inspected/repaired by an authorised REMS
customer service workshop.
Remedy:
● Change the clamping screw and/or centring pin.
● Change the Allen key.
Services under the warranty may only be provided by customer service stations
authorized for this purpose by REMS. Complaints will only be accepted if the
product is returned to a customer service station authorized by REMS without
prior interference in an unassembled condition. Replaced products and parts
shall become the property of REMS.
The user shall be responsible for the cost of shipping and returning the product.
The legal rights of the user, in particular the right to make claims against the
seller under the warranty terms, shall not be affected. This manufacturer's
warranty only applies for new products which are purchased in the European
Union, in Norway or in Switzerland.
This warranty is subject to German law with the exclusion of the United Nations
Convention on Contracts for the International Sales of Goods (CISG).

8. Spare parts lists

For spare parts lists, see www.rems.de → Downloads → Parts lists.
eng
15