Makita LC1230 Manual De Instrucciones página 5

Sierra tronzadora
Ocultar thumbs Ver también para LC1230:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

20. Always use the vise and properly support the
workpiece considering its shape. For example,
Rods and channels have a tendency to roll or shift
while being cut, causing the blade to "bite" and
pull the work with your hand into the blade.
21. Let the blade reach full speed before contact-
ing the workpiece. This will reduce the risk of the
workpiece being thrown.
22. If the workpiece or blade becomes jammed,
turn the power tool off. Wait for all moving
parts to stop and disconnect the plug from
the power source and/or remove the battery
pack. Then work to free the jammed material.
Continued sawing with a jammed workpiece could
cause loss of control or damage to the power tool.
23. After finishing the cut, release the switch,
hold the saw head down and wait for the blade
to stop before removing the cut-off piece.
Reaching with your hand near the coasting blade
is dangerous.
24. Hold the handle firmly when making an incom-
plete cut or when releasing the switch before
the saw head is completely in the down posi-
tion. The braking action of the saw may cause
the saw head to be suddenly pulled downward,
causing a risk of injury.
25. Do not use the metal cutting saw to cut other
than mild steel or stainless steel.
Additional instructions
1.
Intended use
The tool is intended for cutting in mild steel
and stainless steel with appropriate saw
blades.
2.
Never stand on the metal cutting saw. Tipping
over or unintentional contact with the cutting
means could cause serious injury.
3.
Never leave the power tool running unat-
tended. Turn the power off. Do not leave tool
until it comes to a complete stop.
4.
Do not operate saw without guards in place.
Check blade guard for proper closing before
each use. Do not operate saw if blade guard
does not move freely and close instantly.
Never clamp or tie the blade guard into the
open position.
5.
Keep hands out of the path of the saw blade.
Avoid contact with any coasting blade. It can
still cause serious injury.
Always secure all moving portions before
6.
carrying the power tool.
7.
Check the blade carefully for cracks or damage
before operation. Replace cracked or damaged
blade immediately.
8.
Use only flanges specified for this tool.
9.
Always use undamaged flanges and fixing
bolt that are of correct diameter for the blade.
Proper flanges support the blade thus reduc-
ing the possibility of blade breakage.
10. Make sure the shaft lock is released before
turning the power tool on.
11.
Hold the handle firmly. Be aware that the saw
moves up or down slightly during start-up and
stopping.
12. Make sure the blade is not contacting the
workpiece before turning the power tool on.
13. Before using the power tool on an actual work-
piece, let it run for a while. Watch for vibration
or wobbling that could indicate poor installa-
tion or a poorly balanced blade.
14. Stop operation immediately if you notice any-
thing abnormal.
15. Do not attempt to lock the trigger in the "ON"
position.
16. Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive wheels may cause an injury.
17. Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Symbols
The followings show the symbols used for tool.
volts
amperes
hertz
no load speed
alternating current
Class II Construction
revolutions or reciprocation per minute
Do not place hand or fingers close to the
blade.
5 ENGLISH
Tabla de contenido
loading

Tabla de contenido