GE GXCC01D Serie Manual Del Propietário página 4

Usingthe water dispenser.
GXCFOSD
Floor model
GXCF2OE/GXCF2OFBB/GXCF2OKWW/GXCF2OKBB
Chiller model
GXCCOID
Countertop model
Features and Parts List
BottleSupport C ollar (WS28XlO047), greyformodels
GX CFOSD a ndGX CCO1D
BottleSupport C ollar, white(WS28X10049) formodels
GXCF20E andGXCF2OKWW, black(WS28XlO048) for
modelsGXCF2OFBB andGXCF2OKBB
Separator ( WS28XlO013)
0 ColdWaterTank
Hot(Red)andCold (Blue)PowerSwitches(backof
dispenser), Th(, Cold (B]m,) pol_er ,',ldtchalso
turnson thedriller (:ompartment (on models
GXCF2O E/ CXCF2OFN_ / GXCF2OI(W_ _ /'
CXCI:201_I_I_),
Indicator Lights. The green light _411 b e lit _4/en I1_e
dispenseris l/lugged in. "fh_ l_'d and lllne ligNs 1411
_?xle on and t_[lI_l/il_ Ihc disF'ns_'r heats and _ools
water: Compressor start dela) ed b_ up to 3 minut_ s,
Hot(Red) a ndCold (Blue)Water Dispenser B uttons
Dispenser Drip Tray (WS28XIO016) andGrille
(WS28XlO015), greyformodels GXCFOSD andGXCCO1D
Dispenser Drip Tray (WS2.SXlO026) andGrille
(SW28XlO027), whiteformodelsGXCF20E a nd
GXCF20KI44,V
Dispenser Drip Tray (WS2.SXlO031) andGrille
(WS28XIO034), blackformodels GXCF2OFBB and
GXCF2OKBB
Cmnpartment Tray Onodels GXCF2OF./GXCF2OFBB/
GXCF2OKWW/GXCF2OKBB only)(WS29XlO029)
Storage Cmnpartment (GXCFOSD).
Do not u,,_' t _:> s t_/x_toads requiring _Ii'ig_'radon,
The compartment is not refi'iT/rated,
ChillerCmnpartment
(GXCP2ff/GXCF20_B/GXCF_KWW/GXCP_KBB),
The comparm/ent is inl_ nded sold? lilt use in
chilling canned and boxed bexcrag_'s, and packag_'d
nonpel'ishables,
Cmnpartment Shelf(WS28XIO028)
Drainage Cap(f/oorandchi//ermode/s)(WSO1XIO008)
SiliconStopper (floorandchiller models) ( WSO1XIO007)
Retaining Clip(countertop models) ( WSO1XIO010)
Rubber D rainCover (countertop m odels) ( WSO1X10011)
Leading the Dispenser and Start Up
Sanitizethe dispenser water tanks prior toinstalling
a full bottle of water for the first time (see "Cleaning
andSanitizing the Water Tanks").
IMPORTANT" Make sure the dispenser is unplugged
with both the hot and cold power switches (on the
back of the dispenser, on models so equipped) set to
the 0 (off)position. Before placing the water bottle
on the dispenser, wash hands and wipe the top of
the bottle with a clean cloth. Avoid touching the part
of the bottle that wil! be in contact with the water
dispense£
Make sure the water level in the top of the dispenser
is low enough to allow for proper bottle installation.
Failure to do so may cause the dispenser to overflo_z
l. Peel tilt' label tiom the top _over of the
bottle (if l/resent). Do not remox e the entire
l/ottle call.
2. ['lace tile bottle on t()p oflhe dispenser
as
sho/_l, aligning the dispensing _d_e probe to
tile center of tile _ater bottle cap. Press doun
/mdl the probe penetrates the bottle cap,
allowing the horde to rest on the stq_port
eollal;
3. IMPORTANT." P ressboth dispensebuttonsuntil
water runsfrom bothtaps.
4. Plug ill the dispense_:
5. Set the COl l) and ItOT po_wr s_itdles
(located
on the top leI_ rear of the dispenser,
on models so equil/ped) to the I (on) position.
6. Allow 30 minutes/or w_ter to reach hot and
cold telllperattlres.
Contact a local water bottle distributor to purchase
water bottles.