Replacing A Lost Or Broken Control Point - SOMFY RTS 2kW Manual Del Instalador

Pressing a button on the
control point has no effect
on the heating ramp.
Nothing operates.

7.2. Replacing a lost or broken control point

This reset is carried out if all the RTS control
points have been lost or broken.
2QO\ VZLWFK RII WKH SRZHU WZLFH WR WKH +HDWLQJ
Slim Receiver RTS 2kW to be reset!
1) Cut the power supply for 2 seconds.
2) Switch the power supply back on for approximately
 VHFRQGV DW OHDVW  VHFRQGV EXW QR PRUH WKDQ
15 seconds).
 Cut the power supply for 2 seconds.
 Switch the power supply back on: the heating lamp
ÀDVKHV VORZO\
5) %ULHÀ\ SUHVV WKH 352* EXWWRQ RQ WKH QHZ 576
control point: the heating lamp will come on then go
out to indicate that the new RTS control point has
been programmed into the Heating Slim Receiver
RTS 2kW.
7.3. Restoring the RULJLQDO FRQ¿JXUDWLRQ
This reset removes all control points.
2QO\ VZLWFK RII WKH SRZHU WZLFH WR WKH +HDWLQJ
Slim Receiver RTS 2kW to be reset!
1) Cut the power supply for 2 seconds.
2) Switch the power supply back on for approximately
 VHFRQGV IRU DW OHDVW  VHFRQGV EXW QR ORQJHU
than 15 seconds).
 Cut the power supply for 2 seconds.
 Switch the power supply back on: the heating lamp
ÀDVKHV VORZO\
5) 3UHVV WKH 352* EXWWRQ RQ WKH 576 FRQWURO SRLQW
until the heating lamp comes on then goes out
twice in succession: all control points have been
removed.
- Follow the procedures in the section entitled
³&RPPLVVLRQLQJ´ WR DGG 576 FRQWURO SRLQWV
&RS\ULJKW ‹  6RPI\ 6$6 $OO ULJKWV UHVHUYHG
Heating Slim Receiver RTS 2kW / Heating Slim Receiver RTS 2kW Plug
The control point has not been
programmed into the Heating Slim
Receiver RTS 2kW.
The batteries in the control point are
weak.
Radio interference prevents the
operation of the RTS control point and
Heating Slim receiver RTS 2kW.
The control point used is not compatible
with the Heating Slim Receiver RTS
2kW.
The power supply is faulty.
2QH RU PRUH KHDWLQJ ODPSV LV EORZQ
The heating lamp or lamps linked to the
+HDWLQJ 0RG9DU 5HFHLYHU 576 N: DUH
LQ H[FHVV RI  :
Follow the procedure for adding
an RTS control point - see section
HQWLWOHG $GGLQJ5HPRYLQJ
576 FRQWURO SRLQWV 
Replace the batteries, using the same
battery model.
Turn off any radio equipment nearby.
Ensure the two products are
compatible.
Check the power supply.
Replace the heating lamp(s).
Use a more powerful heating receiver.
1 2
OFF
2 sec.
3 4
OFF
2 sec.
5
PROG.
o
1 2
OFF
2 sec.
3 4
OFF
2 sec.
5
PROG.
m
ON
10 sec.
ON
q
p
ON
10 sec.
ON
m
29