Safety Regulations - EINHELL DSL 250/2 Manual De Instrucciones

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Take suitable precautions to protect yourself and
your environment from potential hazards.
•
Never put the pin grinder to any use other
than that intended.
•
Always concentrate while you work. Do not
work if you are tired.
•
Use only a quick-release coupling to connect
up the air supply.
•
It is imperative to use a pressure reducer to
set the working pressure.
•
Never use oxygen or combustible gases as
an energy source.
•
Always disconnect the tool from the air supply
before carrying out any repairs or mainte-
nance work.
•
Use only original replacement parts.
•
Never allow the tool to run unloaded at full
idle speed for any considerable length of time.
•
Wear the necessary protective clothing when
working with the pin grinder.
•
Always wear goggles when grinding.
•
Watch out for sparks when grinding. Hot flying
particles may burn into both soft and hard
materials (glass, floor coverings, etc.) or ig-
nite inflammable solids and liquids (hay, saw
dust, lacquer, etc.).
•
Never use the machine without oil.
•
Check the condition of the grinding pins regu-
larly. n Store the grinder where it is out of the
GB
reach of children.
•
Securely fasten the workpiece you want to
grind.
•
Use only organically bonded grinding wheels
and organically or inorganically bonded grin-
ding pins and small grinding wheels (wheel Ø
smaller than 20 mm).
•
Under no circumstances are you to use grin-
ding wheels at speeds higher than the speed
quoted in min
•
Allow new grinding wheels a running-in peri-
od of 30 seconds on the tool. Operators and
other personnel are to stay out of the danger
zone during the trial run. Hold the rotating
grinding pin away from the body.
•
Never halt a grinding wheel by pressing on its
circumference or face.
•
Tighten the lock nut only enough to hold the
grinding wheel securely in place.
•
Operators are to be thoroughly instructed on
how to use the grinding tool safely.
•
Always examine the grinding pins for signs of
damage before you start to work.
•
Handle grinding pins and other abrasives
•
carefully. Do not drop. Avoid knocks.
•
Make sure the pneumatic motor and the
toolʼs bearings are kept properly lubricated,
particularly after a long period of use.
•
When fitting a grinding pin, be sure to leave a
gap of at least 1 cm between the back of the
abrasive and the tool lock nut.
•
Make sure that the air hose connections
and hose couplings are tight and that the air
pressure is the same as that specified in the
instructions.
•
The grinding/sanding machine should be
configured, adjusted and used only by a q
qualified and trained operators.
•
Make sure that you do not lose the safety in-
formation. Give it to the operator.
•
Never use damaged equipment.
•
If the mounted tool, an accessory part or the
machine itself breaks, pieces may be catapul-
ted away at high speed.
•
Impact-resistant eye protection (safety gog-
gles) must be worn when operating the grin-
ding/ sanding machine. The safety goggles
must be suitable for the intended use.
•
You must make sure that the workpiece is
fixed securely.
•
Cut injuries can occur if loose clothing, jewel-
ry, necklaces, hair or gloves are not kept away
from the machine and its accessory parts.
•
While the machine is being used, the
operatorʼs hands may be exposed to danger
- 12 -
by the wheelʼs manufacturer.
-1