Before First Use; Filling With Fuel; Petrol; Two-Stroke Engine Oil - IKRA IBHS 62 Instrucciones De Manejo

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 59

Before first use

The hedge trimmer is supplied without fuel mixture.
Fill up the tool as described under „Filling with fuel".

Filling with fuel

The tool is operated with a 1:40 mixture of normal
petrol (lead-free) and two-stroke engine oil.
When handling petrol, increased attention is
called for. Avoid smoking and naked flames
due to the risk of explosion.

Petrol:

Octane rating at least 91 ROZ, lead-free
• Do not fill with leaded petrol, diesel or other non-ap-
proved fuels.
• Do not use petrol with an octane rating less than 91
ROZ. This can damage the motor, due to increased
motor temperatures.
• If you are continuously working in the higher rev range,
use petrol with a higher octane rating.
• The use of lead-free petrol is recommended for envi-
ronmental protection reasons. The use of E10 fuels is
not permitted.

Two-stroke engine oil

• According to specification JASO FC or ISO-L-EGC
Do not use any four or two-stroke oils for water-
cooled outboard motors, or premixed products from
petrol stations.

Mixing

Mixing ratio 40:1
Petrol Two-stroke engine
oil (40:1)
1 l
25 ml
2 l
50 ml
• Make sure that you measure the amount of oil pre-
cisely, as a slight difference in a small quantity of oil
can have a significant impact on the mixing ratio.
• Do not alter the mixing ratio, as this will produce more
residue from combustion, increase fuel consumption,
and reduce performance, or the motor may be dam-
aged.
Mix the petrol and the oil in a clean container which is ap-
proved and labelled for fuel, and which is equipped with
an overflow protection device.
1. First pour in half of the petrol required for the mixture.
2. Then add the full amount of the oil.
3. Shake up the mixture.
4. Then pour in the rest of the petrol.
Fuel can only be kept for a limited period, as it ages. Fuel
and fuel mixtures which have been stored for too long
can cause problems when starting the tool. You should
therefore only mix an amount of fuel which you can use
up in a month.
GB | Operating instructions
Petrol
Two-stroke engi-
ne oil (40:1)
5 l
125 ml
10 l
250 ml
Fuels may only be stored in containers which are ap-
proved and labelled for this purpose, in a dry and safe
place.
Make sure that fuel containers are stored in a place
where they will not be accessible to children.

Filling up the hedge trimmer

• Switch off the motor and allow the tool to cool
down!
• Wear protective gloves!
• Avoid contact with the skin or eyes (wear
safety glasses) !
• Pay strict attention to the section „Handling fuel".
23
1. Only fill up the hedge trimmer outdoors or in areas
with adequate ventilation.
2. Clean the area to be used for filling. Dirt in the tank
leads to malfunctions.
3. Shake the container holding the fuel mixture again
before using it for filling.
4. Take care when opening the cap (10), so that any
excess pressure can be dissipated.
5. Pour in the mixture carefully, until it reaches the bottom
edge of the filler neck.
6. Close the petrol cap again.
7. Make sure that the petrol cap is leak-tight.
8. Clean the petrol cap and the surroundings.
9. Pay attention to any leaks from the tank or fuel lines.
10. If necessary, operate the primer pump (23).
11. Before starting the motor, move to a reasonable dis-
tance from the area used for filling.

Operation

The tool may not be put into operation before
you have read these operating instructions, fol-
lowed all the instructions given, and the tool
has been fully and properly assembled!
• Only start the hedge trimmer when it has been fully
assembled.
• Support the hedge trimmer during startup and hold it
securely. Make sure that the cutter is unobstructed.

Starting the hedge trimmer

1. Maintain a safe distance from combustible materials.
7
10
Tabla de contenido
loading

Tabla de contenido