Tabla de contenido
Idiomas disponibles
Idiomas disponibles
If MUSIC MODE is selected, the centre width can be adjusted
with following operations.
This function offers the optimum vocal position by adjusting
the centre channel position between the centre speaker and
the L/R speaker. (The adjustments established in "Adjusting
the acoustic image" (page 35) are ineffective while this
function is activated.)
1) Select CTW_CONT ON/OFF by turning and then
pressing the Rotary encoder.
If ON is set, you can enjoy the optimum vocal position
by distributing the centre channel sound between the
centre speaker and L/R speaker.
2) Adjust the level (LEVEL) by turning and then pressing
the Rotary encoder.
The level can be adjusted between 0 to 7. When the
level increases, the centre channel position moves from
the centre speaker position to both sides.
5
When the setting is complete, press and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press CENTER f. to select another item to be set.
• This adjustment is effective when the setting of the centre speaker
is SMALL or LARGE in the speaker setup settings.
• Avoid stopping, pausing, switching the disc, cueing, fast-
forwarding or switching the audio channel of this unit while
making this adjustment. The setting is cancelled if the Decode
mode is switched.
• This adjustment is ineffective when the speaker is set to CENTER
OFF in "Setting the Speakers" (page 30).
• This function only works with two-channel signals. This operation
is ineffective when 5.1-channel DTS or Dolby Digital signals are
input.
• If the setting of REAR FILL is made when REAR MIX is ON, sound
is unchanged in the rear fill setting because REAR MIX is given
priority during 2 channel decoder other than linear PCM.
• For linear PCM signals, the voice is output from the rear speaker
regardless of the REAR FILL and REAR MIX setting.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 37.
Linear PCM Setting
The output when playing discs recorded in linear PCM can be set to 2
or 3 channels.
1
Check that Defeat mode is off (page 17).
2
Press and hold CENTER f. for at least 2 seconds.
The audio processor control mode is activated.
3
Select the PCM mode by pressing CENTER f.
repeatedly.
4
Select 2 CH or 3 CH by turning and then the
Rotary encoder.
2CH: 2ch output (L/R)
3CH: 3ch output (L/R/CENTER)
5
When the setting is complete, press and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press CENTER f. to select another item to be set.
• This adjustment is ineffective when the speaker is set to CENTER
OFF in "Setting the Speakers" (page 30).
Storing Settings in the Memory
Up to 6 set and adjusted contents can be stored on the unit.
All that are setting and adjusting items described below are stored in
one preset memory.
Setting/adjusting items
Setting the Speakers
Setting Time Correction/Switching Phase/
Setting the Bass Focus
Adjusting EQ
Adjusting X-OVER
Setting MX
Setting BASS COMP.
Setting PRO LOGIC II/Adjusting the
Centre Width*
Adjusting Dolby Surround*
Linear PCM Setting*
* Depending on the input signal, sound effect may not be obtained.
1
Adjust and set the value to be stored.
2
Press and hold for at least 2 seconds any one of
the preset buttons (1 through 6) into which you
want to store the set/adjusted value as preset
memory (MEMORY 1 through MEMORY 6).
• This function is operable only when Defeat is set to OFF.
• The stored contents will not be deleted even when battery power
cord is detached.
Getting out the Preset Memory
1
Check that Defeat mode is off (page 17).
2
Press and hold CENTER f. for at least 2 seconds.
The audio processor control mode is activated.
3
Select the mode to be set by pressing CENTER f.
repeatedly.
4
Press any one of the buttons to select the preset
memory (MEMORY 1 through MEMORY 6) you want
to recall.
• It takes a few moment to get out the preset memory.
Refer to page
30
31, 32, 34
32, 33
30
30
34
36, 37
35
37
37
-EN
Capítulos
Tabla de contenido
