Idiomas disponibles
Idiomas disponibles
Sendebereich, max.
Sendeleistung
Spannungsversorgung:
Wetterstation
Temperatursender
Abmessungen (L x B x H):
Wetterstation
Temperatursender
Haftungsausschluß:
•
Der Hersteller bzw. Lieferant übernimmt keinerlei Verantwortung für
inkorrektes Lesen bzw. für alle Konsequenzen, die durch inkorrektes Lesen
verursacht werden.
•
Dieses Produkt darf nicht für medizinische Zwecke oder zur Information
der Öffentlichkeit eingesetzt werden.
•
Dieses Produkt wurde als Indikator kommender Witterungsbedingungen
für den strikten Heimeinsatz entwickelt und ist nicht zu 100% genau. Die
von diesem Produkt gegebenen Wettervorhersagen und barometrischen
Anzeigen sind deshalb nur als Indikation und nicht als exakte Angabe zu
sehen.
•
Die technischen Daten dieses Produkts können ohne weitere Ankündigung
geändert werden.
•
Dieses Produkt ist kein Spielzeug und gehört deshalb nicht in Kinderhand.
•
Diese Bedienungsanleitung darf ohne schriftliche Einwilligung des
Herstellers auch nicht auszugsweise reproduziert werden.
R&TTE Directive 1999/5/EG
Kurztext der Konformitätserklärung in Landessprache. Wir erklären hiermit,
daß diese Funkanlage die wesentlichen Anforderungen der R&TTE Direktive
1999/5/EG erfüllt.
D
P.22
Features of the Weather Station:
•
Radio controlled time with manual setting option.
•
Current indoor temperature display in degree Celsius.
•
Simultaneous minimum and maximum indoor temperature recordings.
•
Current relative humidity display with "
comfort level reading.
•
3 weather icons for weather forecasting.
•
Weather tendency indicator.
•
Storm warning
•
Relative air pressure in hPa. (Hekto-Pascal) with adjustable reading ranges.
•
Air pressure history for the past 72 hours (electronic barometer with
barometric pressure & trend).
•
Current outdoor temperature display in degree Celsius.
•
Simultaneous minimum and maximum outdoor temperature recordings.
•
Resettable minimum and maximum temperature recordings.
•
LCD contrast changeable to 8 different tones.
•
Low battery indicator.
•
Wall mounting.
Features of the Temperature Transmitter:
•
Remotely transmits outdoor temperature at 433 MHz to the Weather Station.
•
LCD shows the current outdoor temperature in degree Celsius.
•
Shower proof casing.
•
Low battery indicator.
•
With wall mounting holder.
Getting Started
Please follow these steps to ensure that your new Weather Station and
temperature transmitter work correctly together:
Remove all pieces from the packaging and place onto a table in front of you.
Check that you have complete:
1. Weather Station
2. LCD 433 MHz temperature transmitter.
3. Sealed pack with 3 screws and double-sided sticky tape for wall mounting
the transmitter.
GB
P.24
: 25Meter
: -3dBm
: 2 x 1,5V-Batterie Typ AA, IEC LR6
: 2 x 1,5V-Batterie Typ AAA, IEC LR3
: 145 x 31 x 412mm
: 56 x 24 x 80 mm (ohne Haltrahmen)
" Smiling or "
" Sad face for
Introduction:
Congratulations on purchasing this state-of-the-arts Weather Station with radio-
controlled time as an example of fine design and quality piece of engineering.
The operation of this product is easy and straightforward. By reading this
operating manual, users will receive a better understanding of the Weather
Station together with the optimum benefit of all its features.
Weather Station
TIME
HOUR
PM
TEMP °C
INDOOR
MIN°C
MAX°C
HUMDITY
%RH
WEATHER
TENDENCY
LCD
RELATIVE
AIR PRESSURE
hPa
-72
-48
-24
-12
-6
-3
-1
0
PRESSURE
+7
HISTORY
+5
+3
+1
0
-1
-3
-5
-7
TEMP °C
OUTDOOR
MIN°C
MAX°C
433 MHz
RESET
key
LCD Temperature Transmitter
Battery cover
LCD
Battery cover screw
Setting up:
Battery
compartment
Battery cover
SIZE AAA
SIZE AAA
Battery cover screw
1. Firstly, unscrew the screw and open the transmitter's battery cover as
indicated above.
2. Checking the correct polarization, insert 2 x of LR3 (AAA, IEC) 1.5V batteries
into the battery compartment.
3. Replace the cover and screw close whilst ensure the batteries do not spring
free from the contacts as this may cause transmission start up problems.
4. Within 2 minutes of step 3, flip open the cover of the Weather Station.
5. Checking the correct polarisation, insert 2 x LR6 (AA, IEC) 1.5V batteries.
6. Replace the cover whilst ensuring that the batteries do not spring free
from the contacts as this may cause transmission start up problems (should
this happen see Resetting below).
7. Your Weather Station is now operational.
Note: For securing the product into place, please see "Positioning the
Temperature Transmitter" and "Positioning the Weather Station"
below.
When setting up, always remember to insert the batteries into the
transmitter first as this will start the 433 MHz transmission signal for
Hanging Hole
Battery Cover
SET key
+
SET
+
key
Temperature
transmitter holding case
GB
P.23
Battery
compartment
+
SET
Battery cover
GB
P.25
