Idiomas disponibles
Idiomas disponibles
LCD contrast setting
-72
There are 8 different LCD contrast tones to suit the hanging level of the Weather
Station. Simply hang the Weather Station in the desired place and adjust the
contrast so that the LCD digits are sharp and clear from that particular level.
To enter the LCD contrast setting mode press the "SET" key for about 2 seconds
until the word "LCD5" will start flashing in the Relative Air Pressure section.
To adjust simply
1. Press the "+" key to select and go though each of the 8 different contrast
tones.
2. Once the desired contrast tone is selected, press the "SET" key once to
enter the manual time setting mode.
Manual time setting
Hours setting
(flashing)
Following the LCD contrast setting the hour digits in the time display will start
flashing.
1. Using the "+" key, set the required time in hours. Each press will increase
the digits by one.
2. Once the hours are selected, press the "SET" key to move into the minutes
mode.
GB
P.34
hPa setting
-72
Following from the Relative Air Pressure setting, the hPa setting will start
flashing in the Relative Air Pressure hPa section. The hPa can be set between
the ranges of 2 hPa to 4 hPa as follows:-
1. Press the "+" key to select the hPa. Each press or holding the key down
will increase the digits by one.
2. When the desired hPa is selected, press the "SET" key once to return to
the original time mode.
Note: The hPa setting feature can be used in areas where there may be
constant changes in air pressure which do not necessarily reflect the
change in the weather. In such areas for example, the hPa might be
set to every 3 hPa (Hekto-Pascal) meaning that there will be no change
of weather icons if the air pressure does not drop or increase by at
least 3 hPa. For areas where the weather is stagnant, the hPa can be
set lower.
Your Weather Station is now fully set. Please read "Positioning the
temperature transmitter" and "Weather Station" below
Positioning the temperature transmitter:
transmitter holding case
GB
P.36
Flashing
-48
-24
-12
-6
-3
-1
0
+7
+5
+3
+1
0
-1
-3
-5
-7
Minutes setting
(flashing)
Flashing
-48
-24
-12
-6
-3
-1
0
+7
+5
+3
+1
0
-1
-3
-5
-7
Temperature
3. Press the "+" key to set the required time in minutes. Each press will
increase the digits by one.
4. When the time has been set, press the "SET" key. The LCD will now enter
the Relative Air Pressure (hPa) setting mode.
Note: Despite the time being manually set, the Weather Station will
automatically attempt to receive the DCF-77 time signal on every full
hour and when successful, the received time will update the manually
set time.
Relative Air Pressure (hPa) setting
-72
-48
-24
-12
-6
-3
-1
0
Following from the manual time setting mode, the Relative Pressure hPa on
the LCD will start flashing. The Relative Air Pressure hPa range can be set
between 970 hPa to 1030 hPa as follows:-
1. Press the "+" key to change the Relative Air Pressure setting. Each press
or holding the key down will increase the digits by one.
2. When the desired Relative Air Pressure is set, press the "SET" key. The
LCD will now enter the hPa setting mode.
Note: The Relative Air Pressure hPa feature is beneficial for users living at
various altitudes who want for example, to set readings based at sea
level and not from their current surrounding area.
The transmitter is supplied with three screws and double sided sticky tape so
that users can have both option to secure it on a wall by screw or sticky tape.
•
To screw-fix, simply align the screws to the holes in the transmitter holder
and screw-drive all three screws into place (as indicated above)
•
To stick by double sided tape, firstly peel one side of the tape and stick it
firmly onto the back of the transmitter holder and then peel the other side
and press it firmly against the desired wall (as indicated above).
Note: When securing the transmitter, ensure that the 433 MHz frequency
(outdoor temperature) is receivable.
When using the double-sided sticky tape to secure, ensure that the
surface is clean and free from dust or grease. Also do not stick onto
porous and enamel surfaces as these do not make a good permanent
sticking surface over a period of time.
Positioning the Weather Station:
The Weather Station should be wall mounted once it is operational.
Hanging hole
Flashing
+7
+5
+3
+1
0
-1
-3
-5
-7
GB
P.35
5mm
GB
P.37
