Idiomas disponibles
Idiomas disponibles
INTRODUCTION:
Congratulations on your purchase of a Gemini product.
Your product is a state of the art unit, backed by a 1
year limited warranty. With proper care and maintenance,
your unit will provide years of reliable service. Please
register yopur product online at http://www.geminidj.com
or using the included form at the end of this manual.
FEATURES:
GX-200:
Professional Passive ABS Molded speaker
100wattsRMS,250watts peakpower
10"twowayloudspeaker
Compression driver with titanium diaphragm
Aluminum die-cast woofer & high temp voice coil
1/4" Speakon inputs & outputs
Auxiliary line output (for bridging)
Stand mounting sockets for stage monitoring
Full metal grill
Rigging points & easy carry handles
GX-250:
Professional Active ABS Molded speaker
100wattsRMS,250watts peakpower
Powered10"twowayloudspeaker
Compression driver with titanium diaphragm
Aluminum die-cast woofer & high temp voice coil
1/4" & XLR line outputs
1/4" & XLR mic/line inputs
XLR/RCA line inputs
Clip & power LEDs
Built-in mic mixer with bass & treble controls
Auxiliary line output (for bridging)
Stand mounting sockets for stage monitors
Aluminum die-cast woofer & full metal grill
Rigging points & easy carry handles
Voltage selector switch
CAUTIONS:
1. All operating instructions should be read before using this equipment.
2. To reduce the risk of electrical shock, do not open the unit. There are,
NO USER REPLACEABLE PARTS INSIDE
qualified Gemini Sound Products service technician.
3. Do not expose this unit to direct sunlight or to a heat source such as a
radiator or stove.
4. This unit should be cleaned only with a damp cloth. Avoid solvents or
other cleaning detergents.
5. When moving this equipment, it should be placed in its original carton
and packaging. This will reduce the risk of damage during transit.
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE
7. DO NOT USEANY SPRAY CLEANER OR LUBRICANT ONANY
CONTROLS OR SWITCHES
LINE VOLTAGE SELECTION:
The GEMINI GX-250
speakers are a dual voltage unit operating at 115 or
230 volts. Be sure to set the proper voltage:
1. Place the head of a screwdriver in the center of the VOLTAGE
switch found on the rear panel.
SELECTOR (24)
2. Slide the switch to 115 or 230 volts.
3. Do not force or twist the switch. Excessive force may cause damage.
If the switch does not move smoothly, contact a qualified technician.
4. Plug in the GX-250 , using the supplied power cable, into the AC INLET (23)
5. The fuse is located within the AC INLET (23)
fuse of the same value only.
. Please refer servicing to a
.
.
. When replaceing use a
SET-UP:
Use the provided mounting hardware for a STAGE MONITORING
Slide the plastic legs into the holes on the side of the speaker. Refer to
the SET-UP GUIDE
for location. You can also use a SPEAKER STAND
by inserting a stand into the STAND MOUNTING SOCKET (3),
using the LOCKING PIN (8).
the SPEAKER RIGGING POINTS (2),
to hang the speaker where appropriate. Speaker stands and mounting
hardware are available separately. The RUBBER FEET (4)
stacking the speakers on top of each other within the STACKING
located on the top portion of the speaker. Use the EASY
GROOVES (1)
CARRY HANDLE (5)
CONNECTIONS:
Make sure ALL your equipment is completely OFF and lower ALL
VOLUME, LEVEL, & GAIN
1. For the GX-200 use a SPEAKON
to the SPEAKON
LINE OUTPUT
2. For the GX-250 you can connect either a LINE or MICROPHONE
directly into your speaker. For your MIXER you can use either, a
or XLR to XLR CABLE
BALANCED 1/4"
using the RCA (11) or XLR (12) INPUTS
connect a MICROPHONE , you can plug into the MIC 1 input with a 1/4"
or XLR CABLE
to the 1/4" (9) or XLR (10) INPUTS
3. You can also use the AUXILIARY LINE OUTPUT JACKS (7, 13,
an additional speaker using an additional speaker CABLE .
CHAIN-LINK
CHAIN-LINK:
When chain-linking these speakers only 1 GX-200 speaker can be
added to another, but MULTIPLE GX-250
another in a CHAIN-LINK
them and follow the setup steps, your AMPLIFIER
the extra speaker or speakers.
NOTE: PLEASE REFER TO THE CONNECTIONS GUIDE ON PAGE 5 FOR DETAILED INSTRUCTIONS!
OPERATION:
The speakers can be used in PAIRS for a NORMAL setup, or in groups
of FOUR when CHAIN-LINKED
GX-200:
1. First turn on your MIXER or other signal source.
2. Then turn on your AMPLIFIER
control as recommended by the AMPLIFIERS
3. Start playing from your TURNTABLE, CD PLAYER, MIC, etc
the volume controls from your mixer to a reasonable level.
GX-250:
1. First turn on your MIXER/MICROPHONES
turn on your SPEAKER
from your TURNTABLE, CD PLAYER, MIC, etc
controls from your MIXER/MICROPHONES,
2. Use the MIC 1 (15) or LINE IN (16)
levels. The MIC 1/LINE IN LEVEL (15, 16)
LINE IN (11, 12)
be used to adjust the level of the LINE OUT (13, 14)
3. Use the speakers MASTER (17)
level of the SPEAKER,
to adjust the TREBLE
(11, 12) or if the speakers MASTER (17)
will be light up or flash, adjust your volume to a reasonable level.
CLIP LED (21)
.
SPECIFICATIONS:
SEE PAGE 10 FOR SPECIFICATIONS.
SHOULD YOU EXPERIENCE ANY DIFFICULTIES OR PROBLEMS,
PLEASE CALL: 1 (732) 738-9003 FOR GEMINI CUSTOMER SERVICE.
(7)
(7)
(7)
(7)
(7)
Another way to setup the speaker is to use
mounting hardware should be used
for easy transportation.
controls and before connecting the speaker.
from your AMPLIFIER
TM
CABLE
.
TM
INPUT JACK (6)
, or standard RCA CABLES,
to plug into the speaker. To
.
speakers can be added to
setup. After setting up your speakers connect
will compensate for
together.
and increase the VOLUME or GAIN
owner manual.
or other signal source, then
, the POWER LED (22)
will be lit. Start playing
. and adjust the volume
to a reasonable level.
level controls to adjust MIC 1 (9, 10) or
level control to adjust the overall
and use the TREBLE (18)
& BASS (19)
& BASS levels. If your MIC 1 (9,10), LINE 1
level is too loud or distorted the
setup.
tighten
are for
& 14) to
. and adjust
controls can
signals as well.
controls
level
