EINHELL GE-SC 35/1 Li-Solo Manual De Instrucciones Original página 24

Fitting the optional catch basket (see Figs.
11-14)
The basic version of the equipment does not in-
clude a catch basket. This is available separately
(Art. No. 3405576).
•
Push both frame parts into each other (Fig.
11).
•
Pull the grass basket over the metal frame
(Fig. 12).
•
Pull the rubber clips over the metal frame
(Fig. 13).
•
To hang the grass basket on the scarifier you
must lift the ejector flap (Fig. 14/Item 10) with
one hand and with the other hand take hold of
the grass bag by the handle and hook it onto
the scarifier from above (Fig. 14).
Danger!
Before you ever hook the grass basket to the sca-
rifi er you must ensure that the motor is switched
off and the cutting unit is not rotating.
Adjusting the handlebar height (see Fig. 15)
Undo the quick-release levers (Fig. 15/Item 13)
on both sides of the scarifi er.
The height of the handlebar can be set to position
1 or 2 (Fig. 15) during operation. You must then
tighten the quick-release fasteners again.
The same tilt angle must be set on both sides.
Adjusting the scarifi er depth (see Fig. 16)
The scarifi er depth is set with the adjustment me-
chanism. Pull the lever in the direction indicated
by the arrow (see Fig. 16) and adjust to the requi-
red position (0/ 1/ 2/ 3). Make sure that the lever
latches in place correctly!
0 = drive/transport position -3 mm
I = scarifi er depth 3 mm
II = scarifi er depth 6 mm
III = scarifi er depth 9 mm
Charging the battery (Fig. 17/19)
The equipment is supplied without batteries and
without a charger!
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(22) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (21) into the battery
charger (22).
4. In the section entitled „Charger indicator" you
Anl_GE_SC_35_1_Li_SPK9.indb 24 Anl_GE_SC_35_1_Li_SPK9.indb 24
GB
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Installing the battery (Fig. 18-19)
Open the battery cover. This is done by pressing
the lock (A) as shown in Fig. 18 and swinging
up the cover. Then insert the two batteries in the
mounts as shown in Fig. 19 and push them for-
ward until the batteries audibly latch into place.
Note!
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two bat-
teries must always be fully charged before use.
Close the battery cover by swinging it down, and
make sure that it latches in place correctly.
Battery capacity indicator (Fig. 20)
Press the switch for the battery capacity indicator
(Fig. 20/Item A). The battery capacity indicator
(Fig. 20/Item B) shows the charge status of the
battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
- 24 -
20.03.2019 06:16:44 20.03.2019 06:16:44