Tabla de contenido
Idiomas disponibles
Idiomas disponibles
SERVICE AND ADJUSTMENTS
WARNING:
To avoid serious
injury, before
performing any service or adjustments:
1. Be sure the on/off switch is in the
OFF position.
2. Remove safety ignition key.
3. Make sure the augers and all moving
parts have completely stopped.
4. Disconnect
spark plug wire from
spark plug and place wire where it
cannot come in contact with plug.
SNOW THROWER
TO ADJUST SNOW THROWER HEIGHT
See "TO ADJUST SKID PLATES" and "SCRAPER BAR"
in the Operation section of this manual.
CHUTE DEFLECTOR
The chute deflector, attached to the top of the discharge
chute, is provided to direct discharging snow away from
the operator. If the deflector becomes damaged, it should
be replaced.
I &
WARNING:
To avoid serious
injury,
I
never operate your snow thrower with
the deflector removed or damaged.
•
To change direction and/or distance snowis discharged,
see "TO CONTROL SNOW DISCHARGE" in the Op-
eration section of this manual.
SHEAR BOLTS (See Fig. 20)
AUGER SHEAR BOLTS
Both right and left-hand augers are secured to the auger
shaft with a shoulder/shear
bolt and hex nut. Should a for-
eign object or ice become lodged in the augers, the shear
bolts are designed to break, preventing damage to any
other components.
If one or both augers do not turn when
auger control lever is engaged, check to see if one or both
of the bolts have sheared. To replace the shear bolts:
1.
Disengage all controls and move throttle control to
2.
3.
I
STOP position. Wait for all moving parts to stop.
Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
Align hole in auger hub with hole in auger shaft and
install a new 1/4-20 x 2" shoulder/shear
bolt. Install
1/4-20 lock nut and tighten securely.
CAUTION: Do not substitute. Use only original
equipment shear bolts as supplied with your
snow thrower.
4.
Connect spark plug wire to spark plug.
IMPELLER SHEAR BOLTS
The impeller is secured to the impeller shaft with two (2)
capscrew/shear bolts and hex nuts. Should a foreign object
or ice become lodged in the impeller, the capscrews are
designed to break, preventing damage to any other com-
ponents. If impeller does not turn when auger control lever
is engaged, check to see if the capscrews have sheared.
To replace the capscrew/shear
bolts:
1.
Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
2.
Disconnect spark plug wire from spark plug and place
wire where it cannot come in contact with plug.
3.
Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 Iocknuts and tighten securely.
I
4.
CAUTION: Do not substitute. Use only original
equipment capscrew/shear
bolts as supplied
with your snow thrower.
Connect spark plug wire to spark plug.
I
1LO4"c2ONu
T
//_
lC/4A'2S0(_IE 5 1W8/
\
_SHEARBOLT
__
SHAFT
1_-20x2
SHOULDER/
SHEAR BOLT
AUGER
HUB
1_-20
AUGER
LOCKNUT,
HUB
SHAFT
FIG. 20
TO REMOVE BELT COVER (See Fig. 21)
1.
Remove the two (2) screws securing belt cover to
frame.
2.
Remove belt cover.
•
Replace belt cover by installing cover and screws and
tighten securely.
17
FIG. 21
Tabla de contenido
