Additional Safety Rules; Functional Description - Makita 3710 Manual De Instrucciones

ENGLISH
1 Bit protrusion
2 Base
3 Clamping nut
4 Scale
5 Adjusting screw
6 Wing bolt
7 Graduation
8 Wing nut
9 Trimmer shoe
10 Amount of chamfering
11 Switch lever
12 Loosen
13 Tighten
14 Hold
15 Spring washer
16 Flat washer
17 Bolt
SPECIFICATIONS
Model
Collet chuck capacity....................................6 mm or 1/4"
–1
No load speed (min ) .......................................... 30,000
Overall length ..................................................... 302 mm
Net weight ............................................................. 1.6 kg
Safety class .............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for flush trimming and profiling of
wood, plastic and similar materials.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Wear hearing protection during extended peri-
ods of operation.
3. Handle the bits very carefully.
4. Check the bit carefully for cracks or damage
before operation. Replace cracked or damaged
bit immediately.
6
Explanation of general view
18 Workpiece
19 Feed direction
20 Bit revolving direction
21 View from the top of
the tool
22 Straight guide
23 Screws
24 Screwdriver
25 Templet guide
26 Convex portions
27 Straight bit
28 Templet
29 Distance (X)
30 Templet guide
31 Guide plate
32 Clamp screw (A)
33 Centre hole
5.
3710
6.
7.
8.
9.
/II
10. Be careful of the bit rotating direction and the
11. Do not leave the tool running. Operate the tool
12. Always switch off and wait for the bit to come to
13. Do not touch the bit immediately after operation;
14. Always lead the power supply cord away from
15. Do not smear the tool base carelessly with thin-
16. Draw attention to the need to use cutters of the
SAVE THESE INSTRUCTIONS.
ENB054-1

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Adjusting bit protrusion (Fig. 1)
To adjust the bit protrusion, loosen the lever and move
the tool base up or down as desired by pressing and
turning the adjusting roller. After adjusting, tighten the
lever firmly to secure the tool base.
Adjusting angle of tool base (Fig. 2)
Loosen the wing bolts and adjust the angle of the tool base
(5° per graduation) to obtain the desired cutting angle.
34 Nail
35 Clamp screw (B)
36 Trimmer guide
37 Bit
38 Guide roller
39 Not available
40 Not available
41 Not available
42 Not available
43 Not available
44 Not available
45 Not available
46 Not available
47 Not available
48 Limit mark
49 Brush holder cap
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Hold the tool firmly.
Keep hands away from rotating parts.
Make sure the bit is not contacting the work-
piece before the switch is turned on.
Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate improperly installed bit.
feed direction.
only when hand-held.
a complete stop before removing the tool from
workpiece.
it may be extremely hot and could burn your
skin.
the tool towards the rear.
ner, gasoline, oil or the like. They may cause
cracks in the tool base.
correct shank diameter and suitable for the
speed of the tool.