Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Fitting the side handle (fi g. E)
The side handle (9) can be fi tted to suit both Rhand
LH-users.
Always use the tool with the side handle
properly assembled.
•
Loosen the side handle.
•
For RH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the left.
•
For LH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the right.
•
Rotate the side handle to the desired position and
tighten the handle.
Setting the drilling depth (fi g. F)
•
Insert the required drill bit.
•
Slacken the side handle (9).
•
Fit the depth adjustment rod (8) through the hole in
the side handle clamp.
•
Adjust the drilling depth as shown.
•
Tighten the side handle.
Forward/reverse slider (fi g. G)
•
Push the forward/reverse slider (2) to the LH-side for
forward (RH) rotation. See arrows on tool.
•
Push the forward/reverse slider (2) to the RH-side
for reverse (LH) rotation.
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
Replacing the dust cover (fi g. D)
The dust cover (7) prevents dust ingress into the
mechanism. Replace a worn dust cover immediately.
•
Pull back the tool holder locking sleeve (15) and pull
the dust cover (7) off.
•
Fit the new dust cover.
•
Release the tool holder locking sleeve.
Instructions for use
Always observe the safety instructions and
applicable regulations.
•
Be aware of the location of pipework and wiring.
•
Apply only a gentle pressure to the tool (approx.
5 kg). Excessive force does not speed up drilling but
decreases tool performance and may shorten tool life.
•
Do not drill or drive too deep to prevent damage to
the dust cover.
•
Always hold the tool fi rmly with both hands and
ensure a secure stance. Always operate the tool with
the side handle properly mounted.
Proper Hand Position (Fig. H)
WARNING: To reduce the risk of serios
personal injury, ALWAYS use proper hand
position as shown.
WARNING: To reduce the risk of serious
personal injury, ALWAYS hold securely in
anticipation of sudden reaction.
Proper hand position requires one hand on
the side handle (9), with the other hand on
the main handle (14).
Switching on and off (fi g. A)
•
To run the tool, press the variable speed switch (1).
The pressure exerted on the variable speed switch
determines the tool speed.
•
To stop the tool, release the switch.
•
To lock the tool in off position, move the forward/
reverse slider (2) to the central position.
Hammer drilling (fi g. A)
•
Set the mode selector switch (3) to the „hammer
drilling" position.
•
Insert the appropriate drill bit. For best results use
high quality carbide-tipped bits.
•
Adjust the side handle (9) as required.
•
If necessary, set the drilling depth.
•
Mark the spot where the hole is to be drilled.
•
Place the drill bit on the spot and switch on the tool.
Rotary drilling (fi g. A)
•
Set the mode selector switch (3) to the "rotary drilling"
position.
•
Fit a chuck adaptor/chuck assembly. Special SDS-
plus adaptors with threaded sections are available
for use with standard 10 or 13 mm chucks to enable
straight shank bits to be used.
•
Proceed as described for hammer drilling.
Never use standard chucks in the hammer
drilling mode.
Screwdriving (fi g. A)
•
Set the mode selector switch (3) to the "rotary drilling"
position.
•
Select the direction of rotation.
•
Insert the special SDS-plus
for use with hexagonal screwdriver bits.
•
Insert the appropriate screwdriver bit. When driving slotted
head screws always use bits with a fi nder sleeve.
•
Gently press the variable speed switch (1) to prevent
damage to the screw head. In reverse (LH) rotation
the tool speed is automatically reduced for easy
screw removal.
17
E N G L I S H
screwdriving adaptor
®
Tabla de contenido
