Tabla de contenido
Idiomas disponibles
Idiomas disponibles
INSTALLATION
The product may only be installed by a qualified fitter. The manu-
facturer, Tau, declines all liability for damage to property and/or in-
jury to people deriving from the incorrect installation of the system
or its noncompliance with current law (see Machinery Directive).
FIG. 1 - STANDARD SYSTEM
1. Gear motor
2. Release
3. Photocells
4. Posts + Photocells
5. Aerial and Flashing light
6. Key switch
7. Electromechanical edge
8. Gate guide
9. Limit switch shoe
10. Rack
FIG. 2 - INSTALLATION MATERIAL
1. gear motor
2. counterplate
3. rack
4. self-tapping screws
5. limit switch shoes
6. release key
7. rack brackets
8. bent pins for counterplate
Place the control unit (external versions) in the immedi-
ate vicinity of the
motors.
Be careful not to run cables for auxiliary devices in-
side raceways housing other cables supplying power
to large loads or lights with electronic
In the event control pushbuttons or indicator lights are
installed inside homes or offices several metres from
the actual control unit, it is advisable to decouple the
signal by means of a relay in order to avoid induced
interference.
OVERALL DIMENSIONS
Figs. 3,4,5 show the main overall dimensions for the sliding gate;
figs.6-7 show the dimensions of the foundation counterplate, while
fig.8 shows the dimensions of the adjustable counterplate for mod-
els BIG12 and BIG18.
PRELIMINARY OPERATIONS
Carefully read the instructions contained in the handbook before
starting work.
Before proceeding with installation, make sure that all the compo-
nents are present, use suitable work equipment and do not touch
live electrical parts.
CONSIDERATIONS PRIOR TO INSTALLATION
Before proceeding with installation check that:
-
The wheels of the gate are mounted in such a way as to make
it stable and that they are in good condition and perfect working
order;
-
The whole of the slide rail is unobstructed, straight and clean
and a travel stop is fitted at either end.
INSTALLATION DISTANCES
To install the gear motor correctly, make sure it is at a distance of
65 mm from the gate.
See fig. 09 for fixing to a concrete floor, fig. 10 for digging and fig.
11 for positioning the counterplate.
PREPARING THE BASE
Dig foundations at least 15 cm deep and sufficiently wide. Use
protective sheaths for the cables.
FIXING THE FOUNDATION COUNTERPLATE
Fill the hole with concrete and sink the bet pins into it; the coun-
terplate must be perfectly flat at 1 or 2 cm from the level of the
finished floor and at a distance of approximately 65 mm from the
gate.
NB: it is also possible to install the gear motor without the founda-
tion counterplate by using four foundation bolts on a flat concrete
base; the measurements shown in fig. 9 must always be respected.
A height-adjustable counterplate may be used for models BIG12
and BIG18; in this case, the fixed bent pins must be welded to the
rail, see fig. 12/a.
This makes it possible to adapt the gear motor to a pre-existing
system; the measurements shown in fig. 12/b must be respected.
ANCHORING THE GEAR MOTOR
Tighten the screws (as shown in fig. 13) on both sides of the gear
motor. Fit all the cables into the sheath, which passes through the
hole made in the base of the foundation counterplate.
FIXING THE RACK
Prepare the rack with the relative brackets (fig. 14).
Place the rack on the motor pinion (released) respecting the dis-
tance between the tooth of the gear and the tooth of the rack as
shown in fig. 15. Make a hole in the leaf at the centre of the slot
and fix with the relative screws. Slide the leaf along the pinion and
fix each bracket in turn.
starters.
FIXING AND ADJUSTING THE LIMIT SWITCH SHOES
Fix the shoes as shown in fig. 16, one near either end of the rack.
Move the leaf by hand and position the shoes so that they touch
the microswitch lever just before the leaf hits the travel stops at
both ends of the rail; then tighten the screws.
A single factor or combination of factors (thermal ex-
pansion, climate, frequency of use, etc.) may result in
the position the gate stops in changing over the course
of the day, both when opening and when closing. Con-
sequently, we cannot guarantee that the gate will al-
ways stop in the same position.
ADJUSTING THE MECHANICAL CLUTCH
Before starting, make sure to disconnect the gear motor from the
power supply.
BIG12-18:
BIG30-40:
ELECTRICAL CONNECTIONS
For electrical connection, please refer to the specific instructions
for each electrical control panel. The following tips apply to all mod-
els.
Do not put the power cables in the same sheath as the motor ca-
bles. Always choose the shortest routes for the cable lines. Make
sure the equipment is well earthed. A general switch should be
fitted to the system, out of reach of unauthorised people, allowing
power to be disconnected from the gear motor for maintenance
purposes or if the gear motor remains inactive for a long period.
BIG Series
Make a 1/2 or a whole turn at a time using the sup-
plied wrench (fig. 17).
After removing the lock nut (1 fig. 18A) and the stop
dowel (2 fig. 18A), adjust the thrust force using the
hex wrench provided (3 fig. 18B) (rotate clockwise to
increase the thrust force, rotate counter-clockwise
to decrease it). After adjusting as needed, reas-
semble the stop dowel (2 fig. 18D) until it reaches
the mechanical stop, then fasten the lock nut (1 fig.
18D).
11
Tabla de contenido
