IMG STAGELINE WASH-100RGBW Manual De Instrucciones página 10

1) Use the button ENTER to call up the menu
item
Channel Mode
2) Use the button UP or DOWN to select:
(9 channels) or
9 Ch
3) To save the setting and to go back to
the highest menu level, press the button
ENTER .
7.3.3
Slave Mode
Operation as master unit or slave unit
When operating the WASH-100RGBW
without a DMX controller, define the
WASH-100RGBW as a master unit or slave
unit, depending on its type of application
( chapter 7 .2):
☞
1) Use the button ENTER to call up the menu
item .
Slave Mode
2) Use the button UP or DOWN to select:
or
Master Slave
3) To save the setting and to go back to
the highest menu level, press the button
ENTER .
7.3.4
Show Mode
Show program
For operation without a DMX controller, this
menu item can be used to define how the
show program is to be run:
1) Use the button ENTER to call up the menu
item .
Show Mode
2) Use the button UP or DOWN to select:
(automatic program run) or
Auto Run
(music-controlled program run) .
Sound
3) To save the setting and to go back to
the highest menu level, press the button
ENTER .
7.3.5
Backligh
t LCD
Display backlight
1) Use the button ENTER to call up the menu
item
Backlight LCD
2) Use the button UP or DOWN to select:
(display backlight always on) or
On
(display backlight will be switched off
after approx . 1 minute when no button is
pressed; it will be switched on again when
a button is pressed) .
3) To save the setting and to go back to
the highest menu level, press the button
ENTER .
7.3.6
Angle
Pan
Maximum pan angle
The maximum pan angle can be set to 540°
or 630°:
1) Use the button ENTER to call up the menu
item .
Pan Angle
2) Use the button UP or DOWN to select:
or .
540° 630°
3) To save the setting and to go back to
the highest menu level, press the button
ENTER .
10
7.3.7
.
1) Use the button ENTER to call up the menu
(12 channels) .
12 Ch
2) Use the button UP or DOWN to select:
3) To save the setting and to go back to
7.3.8
1) Use the button ENTER to call up the menu
2) Use the button UP or DOWN to select:
.
3) To save the setting and to go back to
7.3.9
When the menu item
up with the button ENTER, a test program will
start: the head will move to a defined position
and will continuously change its colour (red
 green  blue  white  red + green + blue
+ white  ) . To exit the test program and to
go back to the highest menu level, press the
button MENU or ENTER .
7.3.10
The balance between the three primary col-
ours red, green and blue can be shifted; this
will also change the light colour of the white
light that has been created by mixing the
three primary colours . Thus, it is, for example,
.
possible to compensate differences to other
spotlights if they are controlled together with
Off
the WASH-100RGBW .
1) Use the button ENTER to call up the menu
2) Use the button UP or DOWN to select the
3) Use the button ENTER to call up the colour:
4) Use the button UP or DOWN to set the
5) To save the setting and to go back to the
6) If required: select, call up and set the next
7) When all colours have been set as desired,
Inverse
Pan
Inverting the pan direction
item .
Pan Inverse
(inverse pan direction) or
Yes
pan direction) .
the highest menu level, press the button
ENTER .
Tilt Inverse
Inverting the tilt direction
item .
Tilt Inverse
(inverse tilt direction) or
Yes
tilt direction) .
the highest menu level, press the button
ENTER .
Auto Test
Automatic test
Auto Test
White Balance
Colour balance / white balance
item .
White Balance
colour: or or
Red Green Blue
The maximum value set ( ...
0
brightness of the colour will be indicated .
value desired .
previous menu level, press the button
ENTER .
colour; then save the setting .
press the button MENU to go back to the
highest menu level .
7.3.11
Fixture Time
Operating hours
When the menu item
called up with the button ENTER, the num-
ber of operating hours will be indicated . To
go back to the highest menu level, press the
(normal
No
button MENU .
7.3.12
Firmware Version
Firmware version
When the menu item
is called up with the button ENTER, the firm-
ware version (operating system of the unit)
will be indicated . To go back to the highest
menu level, press the button MENU .
7.3.13
System Reset
Resetting the head
(normal
No When the menu item
called up, the head will return to its home
position; then the unit will go back to its pre-
vious operating mode .
Note: When, during DMX operation, one of the pre-
defined colours has been selected in the 12-channel
mode (channel 2: DMX value ≥ 10), the LEDs will
remain dark after the reset . In this case, the WASH-
100RGBW must again receive a DMX command for
the desired colour from the light controller (i . e . briefly
is called
set a different colour, and then go back to the colour
desired) .
8 Specifications
Control protocol: . . . DMX512
Number of
DMX channels: . . . . . 9 or 12
Light source: . . . . . . . 7 × 15 W RGBW LED
Illuminance at
a distance of 2 m: . . . 16 000 lx
Beam angle: . . . . . . . 8°
Pan range: . . . . . . . . 630° max .
Tilt range: . . . . . . . . . 270° max .
DMX connections: . . XLR, 3 poles
Pin configuration: . . pin 1 = ground
Ambient temperature: 0 – 40° C
Power supply: . . . . . . 230 V~/ 50 Hz
Power consumption: . 80 VA
.
Dimensions: . . . . . . . 26 .5 × 33 × 17 cm
) for the
Weight: . . . . . . . . . . 5 .7 kg
255
is
Fixture Time
Firmware Version
is
System Reset
pin 2 = DMX−
pin 3 = DMX+