Bosch GLR500 Instrucciones De Funcionamiento Y Seguridad página 14

When the total measuring distance is somewhat
less than an integral multiple, then a negative
difference and the next higher multiple of the
stake-out value are displayed.
Move the rangefinder until the desired multiple of
the stake-out value is displayed in the center
measured-value line a and the difference in the
bottom measured-value line is a "0.0". Then mark
off the reference point of the measurement.
Examples:
a) Positive difference:
24.3 ft = (12 x 2.0 ft) + 0.3 ft
The stake-out value 2.0 ft is
contained 12 times in a total
distance of 24.3 ft. Additionally,
the total distance contains a rest
of 0.3 ft. Reduce the distance
between the rangefinder and the
starting point by 0.3 ft
difference, and then mark off the length.
b) Negative difference:
23.7 ft = (12 x 2.0 ft) – 0.3 ft
For a total distance of 23.7 ft,
0.3 ft are missing for the mark-
out value 2.0 ft to be contained
12 times. Increase the distance
between the rangefinder and the
starting point by 0.3 ft
difference, and then mark off
the length.
Briefly pressing measuring button 7 ends the
stake-out mode. Press and hold the measuring
button 7 to restart the stake-out mode (with the
same stake-out value).
The stake-out mode automatically switches off
after 5 min. For prior exiting of the function,
push one of the measuring-mode buttons.
List of the last Measuring Values
The rangefinder stores the last 30 measuring
values and their calculations, and displays them
in reverse order (last measured value first).
To recall the stored meas-
urements, push button 15. The
result of the last measurement is
indicated on the display, along
with the indicator for the
measured-value list "d" as well
as a counter for the numbering
of the displayed measurements.
When no further measurements are stored after
pressing button 15 again, the rangefinder
switches back to the last measuring function. To
exit the measured-value list, push one of the
measuring-mode buttons.
To delete the currently displayed measured-value
list entry, briefly push button 16. To delete the
complete measured-value list, press and hold the
button for the measured-value list 15 and at the
same time briefly push button 16.
Deleting Measured Values
Briefly pressing button 16 deletes the last
individual measuring value determined in all
measuring functions. Briefly pressing the button
repeatedly deletes the individual measured
values in reverse order.
In multi-surface area measurement mode, briefly
pressing button 16 the first time deletes the last
individually measured value; pressing the button
a second time deletes all lengths B
pressing the button a third time deletes all room
heights A.
Adding Measured Values
To add measured values, take any measurement
or select an entry from the measured-value list.
Then push the plus button 6. For confirmation, "+"
appears on the display. Then take a second
measurement or select another entry from the
measured-value list.
After calculation of the sum, further measured
values or measured-value list entries can be
added to this result when pressing the plus button
6 prior to each measurement. Pressing the result
button 5 ends the addition.
Notes on the addition:
– Mixture of length, area and volume values
cannot be added together. For example,
when a length and area value are added,
"ERROR" briefly appears on the display after
pressing the result button 5. Afterwards, the
rangefinder switches back to the last active
measuring mode.
– For each calculation, the result of one
measurement is added (e.g. the volume value);
for continuous measurements, this would be
the displayed measured value in result line c.
The addition of individual measured values from
the measured-value lines a is not possible.
– For time-delayed length measurements and
when in stake-out mode, additions are
not possible; when changing to these modes,
begun additions are interrupted.
Subtracting Measured Values
-14-
, and
X
To call up the sum of both
measurements, press the result
button 5. The calculation is
indicated in the measured value
lines a, and the sum in the
result line c.
To subtract measuring values,
push minus button 12; For
confirmation, "–" is indicated on
the display. The further
procedure is analog to "Adding
Measured Values".