Operation Helpful Hints - Bras B-frozen 6-10 Smart Manual De Instrucciones

Power switch (A)
0 position : power is turned OFF to all functions.
I position : power is turned ON to all functions and the
other switches are enabled. The fan motor
runs.
Light switch (E) (if present)
0 position : all top cover lights are OFF.
I position : all top cover lights are ON, provided that
power switch (A) is set to I.
Mixer/refrigeration switch (B)
I position : mixer and refrigeration ON.
SOFT DRINK mode.
0 position : OFF.
II position : mixer and refrigeration ON.
GRANITA mode.
Thermostat (D)
Turn clockwise : to decrease temperature
Turn counterclockwise : to increase temperature
To operate the unit:
1 Set the power switch to I position.
2 Set the mixer/refrigeration switches as follows:
- to the I position to get soft drink.
- to the II position to get Granita.
3 Set the light switch to I position.
ETC VERSION:
Dispenser controls functions are as follows (see figure 1).
Power switch (A)
0 position : power is turned OFF to all functions.
I position : power is turned ON to all functions . The
fan motor runs. On single bowl machines
mixers run too.
Mixer/Refrigeration switches ( C) and (D)
Switch C : if pressed it activates the function 'DRINK'.
In this case the (E) led lights up.
Switch D : if pressed it activates the function 'SLUSH'.
In this case the (F) led lights up.
In machines with several tanks, pressing the key relating to the
activated operating mode will then make it possible to switch off
both mixing and freezing of the corresponding tank. As a result,
the mixer will stop and the two indicator lights (E) and (F) will
switch off. Pressing one of the two keys (C) or (D) makes it
figure 3
possible to reactivate the corresponding function.
Thermostat (B)
It displays the temperature of product inside the bowl.
Temperature alarm : if the temperature on display flashes, it
means that product remained for a certain period at a
temperature higher than the max. admitted conservation
temperature , and therefore it is necessary to check the product
conditions.
Press for three seconds the button (D) to reset the display .
IMPORTANT
If the dispenser is switched on when bowls contain pro-
ducts at a temperature higher than conservation tempe-
rature, the display will flash. To have a fixed display , it
is necessary to press for three seconds the button (D).
IMPORTANT
Conservation temperature is set at the factory at 4°C.
Cleaning mode: hold down key (C) for three seconds to enable
CLEANING mode, during which the display shows " --.-- ". In
this mode, the mixer turns but the cooling is not enabled. This
function is useful during machine rinsing, washing and sanitising
to prevent the contents of the unit from being cooled. It is
nonetheless always possible to quit cleaning mode simply by
pressing any key.
Temperature adjustment in DRINK mode: the optimal
temperature of drinks (when the dispenser works as a drinks
cooler rather than as an ice crusher) is factory set to 4°C. If you
want to adjust the temperature, hold down keys (C) and (D)
simultaneously for two seconds. The indicator light (E) and the
temperature set will flash and you can adjust it using keys (C)
and (D). The display will go blank for a few seconds and then the
current temperature will be displayed.
Minimum temperature adjustment in GRANITA mode: you
can also adjust the minimum temperature of the product when
the dispenser is operating in granita mode. This minimum
temperature is factory set to -10°C. If you want to adjust it, hold
down keys (C) and (D) simultaneously for two seconds to go into
drink temperature adjustment mode and the indicator light (E)
will flash. Press keys (C) and (D) for two seconds to go into
granita minimum temperature adjustment mode and the
indicator light (F) and temperature set will flash. You can adjust
the temperature using keys (C) and (D). The display will go
blank for a few seconds and then the current temperature will be
displayed.
To operate the unit :
4 Set the power switch to I position
5 For each container select :
-Button (C) to get cold drink ( without freezing it)
-Button (D) to get slush
Cleaning function: during sanitizing operations, it may be useful
to have the mixers turning , without cooling. To get this, press for
three seconds the button (C ) : the display of thermostat will
show "--.-- "
By pressing any button, the dispenser will get out from cleaning
function and will operate normally.

7. 2 OPERATION HELPFUL HINTS

1 Granita viscosity adjustment: proper Granita viscosity is
factory preset. To change the viscosity, if needed, use a
standard screwdriver to turn the adjustment screw located in
the rear wall of each container as follows (see figure 4):
- towards right (clockwise) to obtain a thicker product (the indi-
15