Idiomas disponibles
Idiomas disponibles
User instructions
Operating the receiver
Turn on the receiver
- Plug the AC power cord to an 23OV~
outlet nearby and a LED bar on the
display turns ON. The receiver is in
standby mode and ready for use.
- Press
key to turn ON the receiver.
- After viewing the programs, press
key again to turn OFF the receiver to
standby mode.
Programming the receiver
Select
Channel
number
programmed.
Press "SET" key to be in set mode.
Polarity / Band
- Press "SET" key one time and the
display shown Polarity / Band
selection mode.
- Press "+/-" keys to select for 4
modes.
Display
Polarity
Band
U
Vertical
Low
U2
Vertical
High
H
Horizontal
Low
H2
Horizontal
High
IF Frequency
- Press "SET" key for 2nd time and
the reading of IF frequency show on
the display. This can be tuned up or
down with "+/-" keys, or entered
with "0" - "9" digit keys.
- The IF frequency is calculated on
grounds of the following:
IF = Sat. TV freq. - LNB L.O. Freq.
Example: Your
LNB
Is
frequency: 11.475Ghz, If you
want to view the WDF
(12.658GHz) on Kopernikus,
then, set the IF frequency to:
1183 = 12.658 - 11.475.
enter the frequency directly with key
sequence: 1 - 1 - 8 - 3
Programm selection
- A total of 500 programms can be
selected. The programm number
selected is shown on the display.
- Use
key to up/doun programm
selection.
- Entry programm number directly by
using "0" - "9" keys.
TV/SAT Selection
- Press "TV/SAT" key to select TV or
Satellite picture.
to
be
Audio mode & Audio (L) Frequency
- Press "SET" key for 3rd time and the
display shown Audio mode and
frequency.
- Press "AUDIO" key to select for 5
modes of audio receptions:
Display
mode audio band deemph.
S.X.XX stereo
L.X.XX
mono
A.X.XX
mono
J.X.XX
mono
C.X.XX
- The correct audio frequency can be
set by the "+/-" key or entered
directly with "0" - "9" key.
Example: Audio frequency is 7.02
MHz. enter directly with
7 - 0 - 2.
The Use of DiSEqC
- If your receiver has been installed
and connected with Tone Burst or
DiSEqC 1.0 devices, you must turn
ON the DiSEqC function of your
receiver.
The procedures are followings:
with
LO.
Turn ON the DiSEqC function
- Press "D/ON" key to be in DiSEqC
setting mode.
The display show:
This indicates the DiSEqC function of
the receiver is turn ON.
MUTE / Volume regulation
- Press the
sound.
- To turn the volume up, press the
key and to turn the volume down,
press the
- The volume level steps are indicated
in the front display.
Now, the receiver is ready with
DiSEqC function.
Use of DiSEqC 1.0 switch
- Press "SET" key to be in set mode.
The display shows:
Use "LNB" key to select for 4 kinds
of DiSEqC switching.
narrow
DNR
The following table shows the display
narrow
DNR
of these 4 switch and their corres-
ponding.
wide
50µs
DiSEqC commands:
wide
J-17
external audio
Display Option Position Tone Burst
1 XX
1C XX
2 XX
2C XX
- Press "MEM" key to store the proper
DiSEqC switch with the channel in
the memory.
- You can, also, press "MEM" key
after you have completed all of the
programming of the channel.
Turn OFF the DiSEqC function
- Press "D/ON" key to be in DiSEqC
setting mode.
The display shows:
- Press "MEM" key to store this
setting in the memory.
.xxx
23
7229
key to supress the
key.
1 xx
A
A
0
A
B
1
B
A
0
B
B
1
xxx
