Section Ii: Installation; Instructions For Transport; Packaging And Components; Handling Instructions - RHOSS KCMS/PCM Instrucciones De Uso

II

SECTION II: INSTALLATION

II.1

INSTRUCTIONS FOR TRANSPORT

II.1.1

PACKAGING AND COMPONENTS

DANGER !
Do not open or tamper with the p ackaging b efore
installation.
On delivery, chec k that the acc essor y has not been damaged during
transport and that it is c omplete.
If there is visible damage, immediatel y take note of it on the trans port
document by writing: "ACCEPTED WITH RESER VATIONS BECAU SE
OF EVIDENT DAMAGE TO THE PACKAGING", s tating the s erial
number if there ar e several machi nes, since ex-works delivery i mplies
entitlement to c ompensati on from the ins uranc e, in accordanc e with
Law No. 450 of 22/08/85 "terms of refundability" .
Follow the instruction s belo w to remove the p ackaging:
Chec k for visibl e damage;
Open the pac kaging;
Dispose of the pac kaging material in c omplianc e with the applicabl e
regulations, at the appropriate collection or rec ycling centres .
ENVIRONMENTAL PROT ECTION !
Dispose of the p ackaging m aterials in compliance
with the n ational or local legislation in force in your
country.
DANGER !
Do not leave the packaging within r each of childr en.
II.1.2

HANDLING INSTRUCTIONS

DANGER !
The unit must be h andled with car e, in order to
prevent damaging the extern al structure and the
internal m echan ical and electrical components.
Also make sure that ther e are no obst acles or
people along the route, in order to prevent the r isk
of impact, crushing or tipping the lifting vehicle
over.
All the operations listed below must be carried out in accordanc e with
applicable s afety regulati ons, with referenc e to the equipment us ed as
well as the pr ocedures followed.
II.1.3

STORAGE CONDI TIONS

Pac kaged units can be stored by s tac king a maximum of four on top of
each other and must be s tored in a dr y area, away from the s un and
rain.
II.1.4

CLEARANCE AND POSITIONING

IMPORTANT !
Incorrect positioning or in stallation of the unit can
amplif y noise levels and vibrations gener ated
during operation.
II.2 INSTALLATION INS TRUCTIONS
DANGER !
Installation must only b e carried out b y skilled
technicians, qu alified to work on air conditioning
and refriger ation system s. In correct installation
could cau se the unit to malfunction, with a
consequent det erioration in performan ce.
DANGER !
The unit must be in stalled according to nation al or
local regulation s applicable at the time of
installation.
II.2.1 MOUNTING THE CONTROL PANEL
(KPCM - OPTIONAL)
The wall-mounted control panel (KPCM) must be s et up at a mi nimum
height of 1.5 m from the ground. It must also be i nstalled away from
sources of heat.
Use a pointed tool to releas e the bas e from the control panel (see the
figure).
Pass the s hielded c onnecti on c able through the hole on the bas e of the
panel (see the figure on the left). M ount the bas e of the panel to the wall
using two Ø 4 mm screws (see the figure on the right).
After having compl eted the electrical c onnections (see paragraph 0)
close the c ontrol panel by pr essing lightly.
II.2.2

MOUNTING THE RECESSED PANEL (KICM)

The wall-mounted control panel (KPCM) must be s et up at a mi nimum
height of 1.5 m from the ground. It must also be i nstalled away from
sources of heat.
27,3
34
SECTION II: INST ALL ATION
65,2