Removing And Replacing The Belt; Maintenance; Warranty - DeWalt DW718 Manual De Instrucciones

Ocultar thumbs Ver también para DW718:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

CAUTION: Continued use of a platform with several
kerfs may cause loss of material control and possible
injury.
Removing and Replacing Belt
The belt is designed to last the life of the tool. However,
abuse of the tool could cause the belt to fail.
If the blade does not turn when the motor is running, the
belt has failed. To inspect or replace the belt, remove the
belt cover screws. Remove the belt cover. Inspect the ribs
of the belt for wear or failure. Check belt tension by squeez-
ing the belt as shown in Figure 26. The belt halves should
almost touch when squeezing firmly with the thumb and
index finger. To adjust the tension, loosen, but do not
remove, the four Phillips head screws shown. Then rotate
the set screw on the top of the motor plate casting until the
proper tension is achieved. Tighten the four screws
securely and replace the belt cover.
NOTE: Over tightening the belt will cause premature motor
failure.

Maintenance

1. All bearings are sealed. They are lubricated for life and
need no further maintenance.
2. Periodically clean all dust and wood chips from around
AND UNDER the base and the rotary table. Even
though slots are provided to allow debris to pass
through, some dust will accumulate.
3. The brushes are designed to give you several years
of use. If they ever need replacement follow the
instructions on page 8 or return the tool to the nearest
service center for repair. Service center locations are
packed with your tool.
Repairs
To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustments should be performed by a
D
WALT factory service center, a D
E
service center or other qualified service personnel. Always
use identical replacement parts.
Three Year Limited Warranty
D
WALT will repair, without charge, any defects due to
E
faulty materials or workmanship for three years from the
date of purchase. This warranty does not cover part failure
due to normal wear or tool abuse. For further detail of war-
ranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D
E
9258). This warranty does not apply to accessories or
damage caused where repairs have been made or
attempted by others. This warranty gives you specific legal
rights and you may have other rights which vary in certain
states or provinces.
FIG. 24
SCREWS
(two each side)
FIG. 25
FIG. 26
SCREWS
WALT authorized
E
WALT (1-800-433-
In addition to the warranty, D
our:
D
caused by normal use, for free, any time during the first
year after purchase.
If you are not completely satisfied with the performance of
your D
you can return it within 90 days from the date of purchase
with a receipt for a full refund – no questions asked.
RECONDITIONED PRODUCT: Reconditioned product is
covered under the 1 Year Free Service Warranty. The 90
Day Money Back Guarantee and the Three Year Limited
Warranty do not apply to reconditioned product.
FREE WARNING LABEL REPLACEMENT: If your
warning labels become illegible or are missing, call
1-800-4-D
Patent Notification
Manufactured under one or more of the following U.S.
patents:
BACK FENCE
Other patents may be pending.
SET SCREW
13
WALT tools are covered by
E
1 YEAR FREE SERVICE
WALT will maintain the tool and replace worn parts
E
90 DAY MONEY BACK GUARANTEE
WALT Power Tool, Laser, or Nailer for any reason,
E
WALT for a free replacement.
E
6,823,765
6,101,914
5,907,987
6,810,780
6,035,754
5,862,734
6,520,059,
6,032,563
5,582,089
5,375,495
5,285,708
5,199,343
Tabla de contenido
loading

Tabla de contenido