Preparation For Electrical Connections; Product Maintenance - Comunello Automation RAM 220 Instrucciones De Uso

5 PREPARATION FOR ELECTRICAL
CONNECTIONS
WARNING! To connect to the network, use a multipolar cable provided by
regulations by the book's unit.
• Perform the manual release as illustrated in heading 4.4.3.
• Remove the plastic cover as shown in FIG. 10.
• Loosen cable gland "G" located on the lower side of the operator FIG.
10.
• Insert the power cable FIG. 11.
• Connect the wires to the terminal board as shown on the adjacent label.
• Connect the earth wire to the terminal eye next to the terminal board
FIG. 11. (for models of class I).
• Secure the cable by tightening the cable gland.
6 TESTING
Each part of the automation system, e.g. safety edges, photocells,
emergency stop, etc. must be tested; follow the procedures shown in
the instruction manuals supplied with the devices in question. Perform the
following sequence of operations for testing of RAM:
• Check that all the prescriptions in this manual have been followed
scrupulously, with special attention to the matters set down in chapter 1
"Prescriptions".
• Using the supplied control or stopping devices (key selector switch,
control buttons or radio trasmitters), perform gate opening, closing and
stopping tests and make sure the gate responds correctly to the various
commands.
• Check operation of all the system's safety devices (photocells, safety
edges, emergency stop, etc.) one by one.
• If potentially hazardous situations caused by movement of the gate leaf
have been eliminated by limitation of impact force, the associated force
must be measured as prescribed in standard EN 12445.

7 PRODUCT MAINTENANCE

Lubrificate the spindle when needed.
Maintenance must be carried out at regular intervals by qualified personnel in
compliance with the provisions of statutory legislation and the regulations in
force. RAM must be serviced at least once every 6 months or after 10.000
operating cycles since the last service.
• Disconnect the operator from all power supplies
• Check all the moving parts and replace any worn parts.
• Check all parts of the automation system for signs of deterioration.
8 SPARE PARTS
Spare parts can be purchased by contacting technical service.
9 DISPOSAL
At the end of its useful life the automation system must be dismantled by
qualified personnel and the materials must be recycled or disposed of in
compliance with the local legislation in force.
10 WARRANTY
fmndjklsvnbdsjkl Fratelli Comunello SpA provides a warranty for 24 months
for the correct functioning of the actuators from the date of manufacture,
provided that the performance specications indicated in the product
instruction manuals are respected. Free of charge repair and replacement
of components that are found to be faulty according to the indisputable
judgment of the company's technical staff shall be guaranteed at the sole
discretion of Fratelli Comunello Spa, and so excluding any claim for damages
made by others. Warranty material shall be returned to Fratelli Comunello
S.p.a. headquarters carriage paid and will then be shipped to the customer
carriage unpaid. The material found to be faulty and returned to Fratelli
Comunello S.p.a. shall remain property of the Seller. Any cost resulting from
any work needed to repair the defect or to replace the material shall be
charged to the Buyer. No compensation shall be allowed for the period of
device inactivity. Work under warranty does not prolong the warranty period.
The defect of the product shall be reported by the Buyer within 8 (eight) days
from its discovery or from the date of delivery of the goods, under penalty of
invalidation of the warranty. Such claim shall be notied in writing.
Warranty does not cover:
Any product defect or damage that may have been incurred during
transport; any defect or damage arising from any fault and/or from neglect,
inadequacy and misuse of the electrical wiring in the Buyer's property; any
defect or damage caused by any repairs carried out by non authorised
personnel or by incorrect use/installation (with reference to this, system
maintenance is recommended every 6 months) or if not original spare parts
are used; any defect caused by chemicals or atmospheric conditions. The
warranty does not cover any cost neither for consumable materials nor for
alleged defects or convenient surveys.
Product Features Fratelli Comunello SpA products are subjected to
continue changes and improvements; their technical features and image
may therefore change without previous notice.
Competent court
Since the contract of sale is conrmed by an Order Conrmation drawn up
in Rosà, any such dispute shall be settled by the laws of Italy and by the
court of Vicenza (VI).
COMUNELLO ®Copyright 2013 - All right reserved
13