Personal Protective Equipment; Safety Devices On The Product - Husqvarna 115iL Manual De Usuario

you have to move suddenly. Take great care when
you work on sloping ground.
• Keep a good balance and a firm foothold at all times.
Do not overreach.
• Deactivate the product before you move to another
area. Attach the transport guard when the product is
not in use.
•
Never put the product down unless you have
deactivated it. Do not leave the product
unsupervised when it is switched on.
• Remove the battery before you pass the product to
another person.
• Make sure that no clothes or parts of the body come
in contact with the cutting attachment when the
product is activated. Keep the product below waist
level.
• If anything jams in the cutting attachment while you
operate the product, stop and deactivate the product.
Make sure that the cutting attachment stops
completely. Remove the battery before you clean,
inspect or repair the product and/or the cutting
equipment.
• Keep your hands and feet away from the cutting
attachment until it has stopped completely when the
product is deactivated.
• Watch out for stumps of branches that can be thrown
out when you cut. Do not cut to close to the ground
where stones and other objects can be thrown out.
• Watch out for thrown objects. Always wear approved
eye protection. Never lean over the cutting
attachment guard. Stones, rubbish, etc., can be
thrown up into the eyes which can cause blindness
or serious injury.
• Listen out for warning signals or shouts when you
wear hearing protection. Always remove your
hearing protection as soon as the product stops.
• Never work from a ladder, stool or any other raised
position that is not fully secured.
• If any unwanted vibrations occur, tap out new line to
give the line the correct length to stop the vibrations.
• Overexposure to vibration can lead to circulatory
damage or nerve damage in persons who have poor
circulation. Speak to your physician if you
experience symptoms of overexposure to vibration.
Such symptoms include numbness, loss of feeling,
tingling, pricking, pain, loss of strength, changes in
skin colour or condition. These symptoms usually
show in the fingers, hands or wrists.
• Always hold the product with both hands. Hold the
product on the right side of your body.
• Do not remove the cut material, or let other persons
remove cut material, while the product is on or the
cutting equipment rotates, as this can result in
serious injury.
• Always stop the product, remove the battery and
make sure that the cutting equipment does not rotate
before you remove material that is wound around the
blade shaft or caught between the guard and the
cutting attachment.
782 - 001 - 05.07.2019

Personal protective equipment

WARNING: Read the warning instructions
that follow before you use the product.
• Always use approved personal protective equipment
when you use the product. Personal protective
equipment cannot fully prevent injury but it
decreases the degree of injury if an accident does
occur. Let your dealer help you select the right
equipment.
• Use a protective helmet where there is a risk of
falling objects.
(Fig. 19)
• Use approved hearing protection that provides
adequate noise reduction. Long-term exposure to
noise can result in permanent hearing impairment.
(Fig. 20)
• Use approved eye protection. If you use a visor, you
must also use approved protective goggles.
Approved protective goggles must comply with the
ANSI Z87.1 standard in the USAs or EN 166 in EU
countries.
(Fig. 21)
• Use gloves when necessary, for example when you
attach, examine or clean the cutting equipment.
(Fig. 22)
• Use sturdy non-slip boots.
(Fig. 23)
• Use clothing made of a strong fabric. Always use
heavy, long pants and long sleeves. Do not use
loose clothing that can catch on twigs and branches.
Do not wear jewelry, short pants, sandals or go with
bare feet. Put your hair up safely above shoulder
level.
• Keep first aid equipment close at hand.
(Fig. 24)

Safety devices on the product

WARNING: Read the warning instructions
that follow before you use the product.
In this section the product's safety features, its purpose
and how checks and maintenance should be carried out
to ensure that it operates correctly. See instructions
Introduction on page 5 to find where
under the heading
these parts are located on your product.
The life span of the product can be reduced and the risk
of accidents can increase if product maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest servicing dealer.
9