Cycle Status Indicators; Active Vent; Overfill Protection Float - Sears Kenmore ULTRA WASH 665.1602 Serie Manual De Uso Y Cuidado

Heated Dry
The Heated Dry option in combination with rinse aid will give you
excellent drying results. The energy to use Heated Dry costs
pennies per cycle. Heated Dry is on when the light is lit on the
Heated Dry button. Be sure to load plastic items in the upper rack
to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY
so that the light goes off. However, you will have items in your
dish load that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Quick
Rinse.
Lock On
Use the Lock On to prevent unintended use of the dishwasher.
You can also use the lock feature to prevent unintended cycle or
option changes during a cycle.
When LOCK ON is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls
are locked. However, the lock must be turned off and the Start/
Resume button pressed to resume the cycle.
To turn on the Lock
Press and hold HEATED DRY for 4 seconds. LOCK ON glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
NOTE: If the Heated Dry option is selected, the light will
temporarily turn off until Lock On glows.
To turn off the Lock
Press and hold HEATED DRY for 4 seconds. The light turns off.
Delay Hours
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay. After adding items, firmly close the door until it latches and
press START/RESUME, or the delay will not continue.
To delay the start
1. Press the delay button to choose the number of hours
delayed.
2. Select a wash cycle and options.
3. Press START/RESUME.
The dishwasher starts the cycle in the selected number of hours.
NOTES:
• To cancel the delay and cycle, press CANCEL!DRAIN.
• To cancel the delay and start the cycle, press START/
RESUME.
Follow the progress of your dishwasher with the Cycle Status
indicators.
• WASHING
• SENSING
• DRYING
O SANITIZED
O CLEAN
Sensing
Your dishwasher senses the soil level on the dishes. Soil level
determines the length of some cycles, the amount of heat added
to the wash or rinse, and the cycle needed for the load. SENSING
glows during the soil sensing parts of the cycle. Wash action
continues while sensing occurs.
Sanitized
If you select the Sani Rinse option, Sanitized glows when the
Sani Rinse cycle is finished. If your dishwasher did not properly
sanitize your dishes, the light flashes at the end of the cycle. This
can happen if the cycle is interrupted or the incoming water
temperature is too low. The light turns off when you press any
button or close the door.
Clean
Clean glows when a cycle is finished. The light turns off when you
press any button or close the door.
The active vent reduces the sounds from your dishwasher. The
vent closes, after the cycle starts, to lock in sound. The active
vent opens when wash action ends and vapor is vented into
room. Between cycles, the vent stays open for airflow, reducing
the buildup of odors.
NOTE: There is a slight noise when the cover closes or opens.
This is normal.
IMPORTANT: The vapor is hot. Do not touch the vent
during drying.
_.,a •
I • I. I I t
F___,..=.__._ _'<_ -,,--7-2.
The overfill protection float (in the front right corner of the
dishwasher tub) keeps the dishwasher from overfilling. It must be
in place for the dishwasher to operate.
Check under the float for objects that may keep the protector
from moving up or down.
16